Miranda XVP-3901 DENSITE series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 143

background image

GUIDE TO INSTALLATION AND OPERATION

XVP-3901 |

11

REF IN – Studio reference input

For external synchronization, connect a black studio reference signal to the BNC labeled

REF IN

.

•

The loop must be terminated if not used.

The reference input must conform to SMPTE 170M/SMPTE 318M/ITU 624-4/BUT 470-6 for standard definition
signals and SMPTE 274M / SMPTE 296M for high definition signals and is used to phase the HD/SD SDI outputs to
the studio. A reference mismatch may occur if there is a difference between the input video format’s frame rate and
the reference format’s frame rate. When a mismatch occurs, the output will freeze to the reference frame rate and
produce an input error and the card-edge Status LED will turn red to indicate the mismatch.

Note that in the case of HD signals of the same frame rate, any reference signal may be used to genlock any output
signal, regardless of scan type (progressive or interlaced). When a 720p/tri-level sync reference signal is used with an
interlaced output, the output is synchronized but there may be a delay of one field depending on when the
synchronization started.

3G/HD/SD SDI IN – Serial digital HD/SD input

Connect up to two serial digital video signals, conforming to the SMPTE 424M standard for 3G input signals, SMPTE
292M standard for HD input signals or SMPTE 259M standard for SD input signals, to the BNC labeled

HD/SD SDI

IN

. The XVP-3901 will automatically switch to the detected line/frame rate format.

3G/HD/SD SDI OUT – Serial digital video outputs

The XVP-3901 provides two pairs of 3G/HD/SD SDI video outputs on BNC connectors, labeled

3G/HD/SD SDI OUT

A1 & A2,

and

3G/HD/SD SDI OUT B1 & B2

. The SDI video signal conforms to the SMPTE 424M, SMPTE 292M or

SMPTE 259M-C standard.

AES IN / OUT – Discrete AES3 digital audio inputs and outputs (8)

The AES inputs and outputs can be configured for 110 ohm impedance using WECO connectors, or 75 ohm
impedance using BNC connectors. The choice is made through the use of an appropriate rear connector panel.

Rear Panel Type

Connector / Impedance

XVP-3901-110-3TRP-F

WECO 110

Ω

XVP-3901-110-3TRP

WECO 110

Ω

XVP-3901-75-3TRP-F

BNC 75

Ω

XVP-3901-75-3TRP

BNC 75

Ω

To allow for a double-width rear panel, two versions (75

Ω

and

110 Ω)

of a panel with the AES IN and OUT presented

on a 26-pin D-SUB connector are available:

Rear Panel Type

Connector / Impedance

XVP-3901-110-3DRP-F

D-SUB 26

110

Ω

XVP-3901-75-3DRP-F

D-SUB 26

75

Ω

«
...
15
16
17
18
19
...
»

Содержание XVP-3901 DENSITE series
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для XVP-3901 DENSITE series

Бренд: Xantrex Страницы: 152

Бренд: NAD Страницы: 22

Бренд: A-iPower Страницы: 2

Бренд: A-Designs Страницы: 7

Бренд: Racal Instruments Страницы: 12

Бренд: Pulsar Страницы: 4

E-TBT-FRL-FD-01

Бренд: Transition Networks Страницы: 1

Бренд: INVT Страницы: 156

ELinx EIR-G-SFP-T

Бренд: B&B Electronics Страницы: 2

SinePower MSI212

Бренд: Waeco Страницы: 220

Бренд: wagner solar Страницы: 52

Clayton Power 1012

Бренд: LEAB Страницы: 20

Бренд: Hall Research Technologies Страницы: 5

Multi-Decoder MD-2

Бренд: tams elektronik Страницы: 40

Бренд: Beretta Страницы: 8

Бренд: MAKINEX Страницы: 24

Бренд: Meinberg Страницы: 5

Бренд: Arec Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды