background image

14

General Settings

DYNO SETUP

SETUP MODE

7

8
9

10
11
12

14

5

4

3

2

1

5. Factory reset your dyno settings 
6. Set sample rate (Frequency)
7. Set the units of your dyno
8. Set the type of flywheel
9. Set the type of dyno
10 Set the flywheel pulley
11. Set the motor pulley (power source)
12. Number of flywheel markers (black tape on the flywheel)
13. Set the current sensor used
14. Voltage Adjustment 
15. Port #1: for LCD 
16. Port #2: for IR Temp. 
17. Port T1: for Loop Temp. Sensor (Temp #1)
18. Port T2: for Loop Temp. Sensor (Temp #2)
19. Setting Switches 
20. Reset Button

19

20

Electronic Board

To access the settings of your dyno, you must open the main application and select “ Dyno Settings.”

1

Enter Setup Mode

1.1. Open the main application
1.2. Select “Connect Dyno”
1.3. Change 

only

 Switch #8 or #3 to ON. 

1.4. Press the Reset button 1-2 times on the board.
1.5. The Settings application should load automatically.
1.6. (Optional) If the settings application did not load automatically, select “Dyno Settings” 
and follow the screen instructions.

Electronic Board

Switches

Reset Button

NOTE: 

Make sure you have firmware v1.7 or later, and installed the latest application of  

miniPRO Dyno before you continue.

3

Change your Settings

4

Change your Switches

3.1. Select your desired settings
3.2 Select “Save” to complete your settings.

4.1. When finished, select “Disconnect.”
4.2. Change 

only

 Switch #8 to OFF.

4.3. Close the Settings Application.
4.4. Done! The main application should load auto-
matically.

13

15
16

17
18

6

1. Connect/Disconnect the dyno to setup mode
2. Save the settings of your dyno
3. Refresh (re-load) the settings of your dyno
4. Update Firmware Icon

Содержание Slot Car Dyno






















Отзывы: