English
28
●
Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
OPERATION
There are two ways to operate the product:
See illustration section.
●
Single Sequential Actuation - Drive the fastener by pulling
the trigger.
●
Contact (Bump) Actuation - Hold the trigger and drive the
fastener by pushing the nailer against the workpiece.
RELOAD INDICATOR
To indicate that the magazine is almost empty of fasteners
(about 4-5 left), the workpiece contact will not compress,
preventing operation under usual pressure. Install more
fasteners to continue working.
SETTING THE DEPTH OF DRIVE
See illustration section.
Know what is behind your workpiece. A fastener could travel
through the workpiece and out the other side, striking a
bystander and causing serious injury. Lower the depth of drive
to prevent the fastener from being pushed all the way through
the workpiece.
CLEARING A JAMMED FASTENER
Most jams are caused by a fastener or part of a fastener
wedging between the driver blade and the nail guide. Fastener
strips with an incorrect collation angle or the wrong fastener
gauge may cause continuous jamming.
Follow these steps to clear a jammed fastener:
1. Remove the battery pack.
WARNING!
Always point the product away from yourself
and others when installing or removing fasteners. Failure
to do so could result in injury.
2. Remove the fastener strip from magazine.
3. Remove the fastener using needle-nose pliers. If
necessary, remove the magazine from the product.
4. Follow the steps under "Required Daily Testing" before
restarting the work.
REQUIRED DAILY TESTING
WARNING! To reduce the risk of injury to yourself and
others, test the product before beginning work each day
or if the product is dropped, has received a sharp blow,
has been run over, etc. Complete the following checklist
in order. If the product does not work as it should, contact
a MILWAUKEE service facility immediately.
Always point the product away from yourself and others.
1. Remove the battery pack.
WARNING!
Always point the product away from yourself
and others when installing fasteners. Failure to do so could
result in injury.
2. Check all screws, bolts, nuts, and pins on the product.
Tighten any loose fasteners.
3. Pull back the fastener pusher on the magazine (to override
the Reload Indicator), and press the workpiece contact
against a workpiece. The operation should move smoothly.
4. With the workpiece contact pressed against the workpiece,
pull the trigger. The operation should move smoothly.
5. Insert the battery pack.
6. Select the Single Sequential Actuation Operation.
a) Without pulling the trigger, pull back the fastener pusher
on the magazine and press the workpiece contact
against the workpiece. The product should not operate.
b) Holding the workpiece contact away from the workpiece,
pull back the fastener pusher on the magazine. Pull and
hold the trigger for 5 seconds. The product should not
operate.
c) Continue to pull and hold the trigger, and push the
workpiece contact against a workpiece. The product
should not operate.
d) Without pulling the trigger, pull back the fastener pusher
on the magazine, and press the workpiece contact
against a workpiece. Pull the trigger. The product
should operate.
e) Release the trigger. The driver should move up.
7. Select the Contact Actuation Operation.
a) Holding the workpiece contact away from the workpiece,
pull back the fastener pusher on the magazine, and pull
the trigger. The product should not operate.
b) Continue to pull and hold the trigger and push the
workpiece contact against a workpiece. The product
should operate.
8. If all previous tests work properly, set the product for your
work. Select the operation, and load fastener strips.
9. Set the depth of drive according to the "Setting the Depth of
Drive" section, and see illustration section.
10. If the product passes all the tests, the product is ready for
use. Repeat the tests before every use or if the product is
dropped, has received a sharp blow, has been run over, is
jammed, etc.
MAINTENANCE
Keep the ventilation slots of the product clear at all times.
Use only MILWAUKEE accessories and spare parts. Should
components that have not been described need to be replaced,
contact one of our MILWAUKEE service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the product can be ordered.
State the product type and the serial number on the label, and
order the drawing at your local service centres.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting
any work on the product.
Read the instructions carefully before
starting the product.
Always wear goggles when using the
product.
Содержание M18 FFN21
