Milton Roy MILROYAL G Скачать руководство пользователя страница 27

Страница: 27 / 48

Instruction Manual

B. Installation of New Diaphragm

(Figures 7 & 8)

1. Make sure the contoured diaphragm support

surface and O-ring groove machined into
displacement chamber are clean. To prevent
leakage from occurring, be careful not to scratch
the O-ring groove when cleaning.

2. Install the diaphragm into the displacement

chamber with the black rubber side against
the contoured surface of the displacement
chamber. Make sure the diaphragm sealing

bead fits securely in the diaphragm groove of the
displacement chamber. The white teflon-face of

the diaphragm should be facing outward and
visible.

3. Align the two holes in the diaphragm head with the

locating pins (610) in the displacement chamber
and reinstall diaphragm head (1020).

4. Reinstall head bolts (1025), flat washer (1040),

lock washers (1035), and nuts (1030).

5. Tighten bolts firmly in a crisscross pattern.

4.4.5 Removal of Pump Liquid End

(Figures 7 & 8)

MILROYAL

G liquid ends are designed to

provide reliable service under normal operating
circumstances and should not require removal

of the liquid end. However, if the need arises, the

following describes the procedure.

BEFORE BEGINNING DISASSEMBLY
PROCEDURES, RELIEVE ALL

PRESSURE FROM SYSTEM, ISOLATE THE LIQUID END FROM ALL
SOURCES OF PROCESS LIQUID WITH APPROPRIATE VALVING, AND
PURGE LIQUID END OF ALL PROCESS LIQUID.

A. Disassembly:

1. Disconnect both the suction inlet and discharge

outlet from the piping system.

2. Drain oil as described in the above “Oil

Replacement” section of this manual.

3. Remove 3- Function Valve assembly as

described in the “Start- Up of Pump Containing
No Oil in Casing and Displacement Chamber”.

4. Remove six displacement chamber bolts (570)

and lock washers (560) which secure liquid end

to pump drive housing.

5. Locate a container under liquid end to catch

approximately 1 pint of oil that will escape during

next step.

6. Gently pull liquid end OFF drive housing

being careful to avoid damage to plunger

(520,

figure 5

) during removal. Drain oil into

waste container.

7. Discard displacement chamber gasket (590).

8. Place the liquid end, diaphragm head up, on

a bench or other clean, flat, convenient work

area.

B. Reassembly:

1. Make sure gasket surface on pump housing

and displacement chamber are clean and free
of markings which could serve as leak paths.

2. Install new displacement chamber gasket (590)

in correct orientation on liquid end.

3. With vent cap (620) at 12 O’clock, gently slide

liquid end over plunger.

4. Reinstall six displacement chamber bolts (570)

and lock washers (560) and tighten securely.

5. Follow procedure for filling pump housing

and liquid end with oil described in “Start- Up

of Pump Containing No Oil in Casing and
Displacement Chamber”.

SECTION 4 - MAINTENANCE

Содержание MILROYAL G

















































Результаты поиска

Содержание MILROYAL G

Отзывы:

Похожие инструкции для MILROYAL G

Бренды по названию

Популярные бренды

Milton Roy MILROYAL G, Инструкция по эксплуатации

Результаты поиска

Содержание MILROYAL G

Отзывы:

Похожие инструкции для MILROYAL G

Бренды по названию

Популярные бренды