ENGLISH
OM-363 Page 51
6-2. Troubleshooting The Welding Power Source
Refer to Section 6-1 for any Help (
HLP
) message displayed on voltmeter/ammeter.
NOTICE
−
The remedies listed below are recommendations only. If these remedies do
not fix the trouble with your unit, have a Factory Authorized Service Agent check unit.
There are no user serviceable parts inside unit.
Trouble
Remedy
No weld output; unit completely
inoperative.
Place line disconnect switch in On position (see Section 3-21).
Check and replace line fuse(s), if necessary (see Section 3-21).
Check for proper input power connections (see Section 3-21).
Check for proper jumper link position (see Section 3-20).
No weld output; unit on.
If using remote control, place Output control in Remote 14 position, and make sure remote control is
connected to Remote 14 receptacle. If remote is not being used, place Output control in On position
Check, repair, or replace remote control.
Have Factory Authorized Service Agent check unit.
Unit provides only maximum or
minimum weld output.
Make sure Amperage control is in proper position (see Section 4-1).
Have Factory Authorized Service Agent check unit.
Erratic or improper weld output.
Use proper size and type of weld cable (see Section 3-8).
Clean and tighten all weld connections.
Check position of Output Selector control (see Section Figure 4-1).
If using remote control, check position of Amperage Adjustment control (see Section 4-1).
No control of weld output.
If using remote control, place Output control in Remote 14 position, and make sure remote control is
connected to Remote 14 receptacle. If remote is not being used, place Output control in On position
Make sure Amperage control is in proper position (see Section 4-1).
No output from duplex receptacle RC2
and no high frequency.
Reset circuit breaker CB1 (see Section 5-3).
Lack of high frequency; difficulty in
starting GTAW arc.
Reset circuit breaker CB1 (see Section 5-3).
Select proper size tungsten (see Section 9).
Be sure torch cable is not close to any grounded metal.
Check cables and torch for cracked insulation or bad connections. Repair or replace.
Check spark gaps (see Section 5-4).
Wandering arc
−
poor control of
direction of arc.
Reduce gas flow rate.
Select proper size tungsten (see Section 9).
Properly prepare tungsten (see Section 9).
Tungsten electrode oxidizing and not
remaining bright after conclusion of
weld.
Shield weld zone from drafts.
Increase postflow time.
Check and tighten all gas fittings.
Properly prepare tungsten.
Check for water in torch, and repair torch if necessary.
Fan not operating.
Unit equipped with Fan-On-Demand
. Fans run only when necessary. Unit equipped with circuitry to
protect against overheating.
Содержание Syncrowave 250 DX
