Miller Syncrowave 250 DX Скачать руководство пользователя страница 31

Страница: 31 / 82

ENGLISH

OM-363 Page 25

3-21. Connecting Input Power

Installation must meet all National and

Local Codes

−

have only qualified per-

sons make this installation.

Disconnect and lockout/tagout input

power before connecting input con-

ductors from unit.

Make input power connections to the

welding power source first.

Always connect green or green/yellow

conductor to supply grounding termi-

nal first, and never to a line terminal.

See rating label on unit and check input volt-

age available at site.
1

Input Power Conductors (Customer

Supplied Cord)

Select size and length of conductors using

Section 3-19. Conductors must comply with

national, state, and local electrical codes. If

applicable, use lugs of proper amperage

capacity and correct hole size.

Welding Power Source Input Power Con-

nections

Strain Relief

Route conductors (cord) through strain relief

and tighten screws.

Machine Grounding Terminal

Green Or Green/Yellow Grounding

Conductor

Connect green or green/yellow grounding

conductor to welding power source grounding

terminal first.

Welding Power Source Line Terminals

Input Conductors L1 And L2

Connect input conductors L1 and L2 to weld-

ing power source line terminals.

Close and secure access door on welding

power source.

Disconnect Device Input Power Connec-

tions

Disconnect Device (switch shown in

OFF position)

Disconnect Device (Supply) Grounding

Terminal

Connect green or green/yellow grounding

conductor to disconnect device grounding ter-

minal first.
9

Disconnect Device Line Terminals

Connect input conductors L1 and L2 to

disconnect device line terminals.
10 Overcurrent Protection
Select type and size of overcurrent protection

using Section 3-19 (fused disconnect switch

shown).

Close and secure door on line disconnect de-

vice. Remove lockout/tagout device, and

place switch in the On position.

803 585-C

3/8 in

Tools Needed:

=GND/PE Earth Ground

Содержание Syncrowave 250 DX



















































































Результаты поиска

Содержание Syncrowave 250 DX

Отзывы:

Похожие инструкции для Syncrowave 250 DX

Бренды по названию

Популярные бренды

Miller Syncrowave 250 DX, Руководство пользователя

Результаты поиска

Содержание Syncrowave 250 DX

Отзывы:

Похожие инструкции для Syncrowave 250 DX

Бренды по названию

Популярные бренды