Miller Syncrowave 250 DX Скачать руководство пользователя страница 58

Страница: 58 / 82

OM-363 Page 52

6-3. Routine Maintenance For Optional Cooler

Disconnect power

before maintaining.

= Check

= Change

= Clean

= Repair

= Replace

* To be done by Factory Authorized Service Agent

Every

Month

NOTICE

−

Clean coolant strainer.

Severe con-

ditions may require more frequent cleaning

(continuous use, high/low temperatures, dirty

environment, etc.).

Failure to properly

clean coolant strainer voids pump war-

ranty.

Coolant Strainer

Heat Exchanger Fins

Every

Six

Months

Unreadable Labels

Cracked Hoses

Change Coolant If Using Water (See

Section 6-5)

Every

Twelve

Months

Change Coolant (If Using Miller Cool-

ant) (See Section 6-5)

6-4. Troubleshooting The Optional Cooler

Trouble

Remedy

Coolant system does not work.

Be sure input power cord is plugged in to energized receptacle.

Check line fuses or circuit breaker, and replace or reset if necessary.

Motor overheated. Unit starts running when motor has cooled.

Have Factory Authorized Service Agent check motor.

Decreased or no coolant flow.

Add coolant.

Check for clogged hoses or coolant filter.

Disconnect pump, and check for sheared coupling. Replace coupling if necessary.

Содержание Syncrowave 250 DX



















































































Результаты поиска

Содержание Syncrowave 250 DX

Отзывы:

Похожие инструкции для Syncrowave 250 DX

Бренды по названию

Популярные бренды

Miller Syncrowave 250 DX, Руководство пользователя

Результаты поиска

Содержание Syncrowave 250 DX

Отзывы:

Похожие инструкции для Syncrowave 250 DX

Бренды по названию

Популярные бренды