Miller Syncrowave 250 DX Скачать руководство пользователя страница 56

Страница: 56 / 82

OM-363 Page 50

SECTION 6

−

TROUBLESHOOTING

6-1. Voltmeter/Ammeter Help Displays

HLP

--1

HLP

--2

HLP

--3

HLP

--4

HLP

--5

HLP

--9

HLP

-10

HLP

-11

HLP

--0

HLP

-12

All directions are in reference to the front of the unit. All cir-
cuitry referred to is located inside the unit.

Help 0 Display

Indicates a short in the thermal protection circuitry located on the

transformer/stabilizer of the unit.

Help

Display

An SCR overcurrent or undercurrent condition has occurred.

Turn power off and back on to correct condition.

Help

Display

Indicates an open in the thermal protection circuitry located on

the transformer/stabilizer of the unit.

Help

Display

Indicates the transformer/stabilizer of the unit has overheated.

The unit has shut down to allow the fan to cool it (see Section

3-6). Operation will continue when the unit has cooled.

Help

Display

Indicates an open in the thermal protection circuitry located on

the rectifier assembly of the unit.
5

Help

Display

Rectifier assembly has overheated. The unit has shut down to

allow the fan to cool unit (see Section 3-6). Operation will contin-

ue when the unit has cooled.
6

Help

Display

Indicates a short in the thermal protection circuitry located on the

rectifier assembly of the unit.
7

Help

Display

Indicates Remote Output control is activated. Release Remote

Output control to clear help message.
8

Help

Display

Output Selector switch is not in correct position (see Section

4-2).
9

Help

Display

Indicates a non-allowable set-up of the front panel.

Содержание Syncrowave 250 DX



















































































Результаты поиска

Содержание Syncrowave 250 DX

Отзывы:

Похожие инструкции для Syncrowave 250 DX

Бренды по названию

Популярные бренды

Miller Syncrowave 250 DX, Руководство пользователя

Результаты поиска

Содержание Syncrowave 250 DX

Отзывы:

Похожие инструкции для Syncrowave 250 DX

Бренды по названию

Популярные бренды