Miller Electric CE-60T Скачать руководство пользователя страница 7

Страница: 7 / 60

OM-242 880 Page 3

1-3. Additional Symbols For Installation, Operation, And Maintenance

HOT PARTS can burn.

Do not touch hot parts bare handed.

Allow cooling period before working on

equipment.

To handle hot parts, use proper tools and/or

wear heavy, insulated welding gloves and

clothing to prevent burns.

MOVING PARTS can injure.

Keep away from moving parts such as fans.

Keep all doors, panels, covers, and guards

closed and securely in place.

Have only qualified persons remove doors, panels, covers, or

guards for maintenance and troubleshooting as necessary.

Reinstall doors, panels, covers, or guards when maintenance is

finished and before reconnecting input power.

READ INSTRUCTIONS.

Read and follow all labels and the Owner’s

Manual carefully before installing, operating, or

servicing unit. Read the safety information at

the beginning of the manual and in each

section.

Use only genuine replacement parts from the manufacturer.

Perform maintenance and service according to the Owner’s

Manuals, industry standards, and national, state, and local

codes.

FLYING METAL or DIRT can injure eyes.

Wear safety glasses with side shields or wear

face shield.

ELECTRIC AND MAGNETIC FIELDS (EMF)
can affect Implanted Medical Devices.

Wearers of Pacemakers and other Implanted

Medical Devices should keep away.

Implanted Medical Device wearers should consult their doctor

and the device manufacturer before going near arc welding, spot

welding, gouging, plasma arc cutting, or induction heating

operations.

OVERUSE can cause OVERHEATING.

Allow cooling period; follow rated duty cycle.

Reduce amperage (thickness) or reduce duty

cycle before starting to cut again.

EXPLODING HYDROGEN hazard.

When cutting aluminum underwater or with the

water touching the underside of the aluminum,

free hydrogen gas may collect under the work-

piece.

See your cutting engineer and water table instructions for help.

FALLING EQUIPMENT can injure.

Use lifting eye to lift unit only, NOT running

gear, gas cylinders, or any other accessories.

Use equipment of adequate capacity to lift unit.

If using lift forks to move unit, be sure forks are long enough to ex-

tend beyond opposite side of unit.

Keep equipment (cables and cords) away from moving vehicles

when working from an aerial location.

Follow the guidelines in the Applications Manual for the Revised

NIOSH Lifting Equation (Publication No. 94

−

110) when manually

lifting heavy parts or equipment.

FIRE OR EXPLOSION hazard.

Do not locate unit on, over, or near combustible

surfaces.

Do not install unit near flammables.

Do not overload building wiring

−

be sure power supply system is

properly sized, rated, and protected to handle this unit.

STATIC (ESD) can damage PC boards.

Put on grounded wrist strap BEFORE handling

boards or parts.

Use proper static-proof bags and boxes to

store, move, or ship PC boards.

H.F. RADIATION can cause interference.

High frequency (H.F.) can interfere with radio

navigation, safety services, computers, and

communications equipment.

Have only qualified persons familiar with elec-

tronic equipment perform this installation.

The user is responsible for having a qualified electrician promptly

correct any interference problem resulting from the installation.

If notified by the FCC about interference, stop using the equipment

at once.

Have the installation regularly checked and maintained.

Keep high-frequency source doors and panels tightly shut, keep

spark gaps at correct setting, and use grounding and shielding to

minimize the possibility of interference.

ARC CUTTING can cause interference.

Electromagnetic energy can interfere with

sensitive electronic equipment such as

computers and computer-driven equipment

such as robots.

To reduce possible interference, keep cables as short as possible,

close together, and down low, such as on the floor.

Locate cutting operation 100 meters from any sensitive electronic

equipment.

Be sure this cutting power source is installed and grounded

according to this manual.

If interference still occurs, the user must take extra measures such

as moving the machine, using shielded cables, using line filters, or

shielding the work area.

Содержание CE-60T





























































Результаты поиска

Содержание CE-60T

Отзывы:

Похожие инструкции для CE-60T

Бренды по названию

Популярные бренды

Miller Electric CE-60T, Руководство пользователя

Результаты поиска

Содержание CE-60T

Отзывы:

Похожие инструкции для CE-60T

Бренды по названию

Популярные бренды