Miller Electric Big Blue 400 KX Скачать руководство пользователя страница 27

Страница: 27 / 72

OM-4423 Page 21

5-7. Connecting To Weld Output Terminals

MIG and FCAW Welding

For MIG and FCAW welding Direct Current

Electrode Positive (DCEP, connect wire feed-

er cable to CV (Wire) terminal on right and

work cable to Work/Negative (

−

) terminal on

left. Use Process/Contactor switch to select

type of weld output (see Section 6-3).
For Direct Current Electrode Negative

(DCEN), reverse cable connections.

Tools Needed:

3/4 in

Ref 803 843

−

B / 217 358-B / 803 778-A

Do not place

anything between

Correct Installation

Incorrect Installation

weld cable terminal

and copper bar.

Stop engine.

Work (

−

) Weld Output Terminal

CV (Wire) Weld Output Terminal

CC (Stick/TIG) Weld Output Terminal

Failure to properly connect weld

cables may cause excessive heat and

start a fire, or damage your machine.

Weld Output Terminal

Supplied Weld Output Terminal Nut

Weld Cable Terminal

Copper Bar

Remove supplied nut from weld output termi-

nal. Slide weld cable terminal onto weld output

terminal and secure with nut so that weld cable

terminal is tight against copper bar.

Do not

place anything between weld cable termi-

nal and copper bar. Make sure that the sur-

faces of the weld cable terminal and cop-

per bar are clean.

Stick and TIG Welding

For Stick and TIG welding Direct Current Elec-

trode Positive (DCEP), connect electrode

holder cable to CC (Stick/TIG) terminal on

right and work cable to Negative (

−

) terminal

on left.
For Direct Current Electrode Negative

(DCEN), reverse cable connections.
Use Process/Contactor switch to select type

of weld output (see Section 6-3).

Содержание Big Blue 400 KX









































































Результаты поиска

Содержание Big Blue 400 KX

Отзывы:

Похожие инструкции для Big Blue 400 KX

Бренды по названию

Популярные бренды

Miller Electric Big Blue 400 KX, Руководство пользователя

Результаты поиска

Содержание Big Blue 400 KX

Отзывы:

Похожие инструкции для Big Blue 400 KX

Бренды по названию

Популярные бренды