Miller Electric Big Blue 400 KX Скачать руководство пользователя страница 52

Страница: 52 / 72

OM-4423 Page 46

10-3. Run-In Procedure Using Resistance Grid

S-0684

Stop engine.

Do not touch hot exhaust

pipe, engine parts, or load

bank/grid.

Keep exhaust and pipe away

from flammables.

Do not perform run-in

procedure at less than 20

volts weld output and do not

exceed duty cycle or equip-

ment damage may occur.

Resistance Grid

Use grid sized for generator rated

output.
Turn Off grid.
2

Welding Generator

Place V/A control in minimum posi-

tion, and Output Selector switch (if

present) in either DC position.
3

Weld Cables

Connect grid to generator weld

output terminals using proper size

weld cables with correct connec-

tors (polarity is not important).
4

Voltmeter

Clamp-On Ammeter

Connect voltmeter and ammeter as

shown, if not provided on generator.
Start engine and run for several

minutes.
Set grid switches and then adjust

generator A/V control so load

equals rated voltage and current of

the generator (see nameplate, rat-

ing label, or the specifications sec-

tion in this manual).
Check generator and meters after

first five minutes then every fifteen

minutes to be sure generator is

loaded properly.

Check oil level frequently dur-
ing run-in; add oil if needed.

After one hour (minimum), place

A/V control in minimum position,

then shut down grid to remove load.

Run engine several minutes at no

load.

Stop engine and let cool.

Engine Exhaust Pipe

Repeat procedure if wetstacking is

present.

Содержание Big Blue 400 KX









































































Результаты поиска

Содержание Big Blue 400 KX

Отзывы:

Похожие инструкции для Big Blue 400 KX

Бренды по названию

Популярные бренды

Miller Electric Big Blue 400 KX, Руководство пользователя

Результаты поиска

Содержание Big Blue 400 KX

Отзывы:

Похожие инструкции для Big Blue 400 KX

Бренды по названию

Популярные бренды