Miller Electric Big Blue 400 KX Скачать руководство пользователя страница 23

Страница: 23 / 72

OM-4423 Page 17

5-2. Mounting Welding Generator

Tools Needed:

9/16 in

Welding Unit In Place

Bolting Unit In Place

Do not weld on base. Weld-

ing on base can cause fuel

tank fire or explosion. Weld

only on the four mounting

brackets or bolt unit down.

Do not mount unit by sup-

porting the base only at the

four mounting brackets.

Use cross-supports to ade-

quately support unit and pre-

vent damage to base.

Mounting Surface:

Cross-Supports

Mounting Brackets (Supplied)

Mount unit on flat surface or use

cross-supports to support base.

Secure unit with mounting brack-

ets.
3

1/2 in Bolt And Washer

(Minimum

−

Not Supplied)

3/8-16 x 1 in Screws

(Supplied)

To Bolt Unit In Place:

Remove hardware securing the

four mounting brackets to the base.

Reverse brackets and reattach to

base with original hardware.
Mount unit to truck or trailer with 1/2

in (12 mm) or larger hardware (not

supplied).

To Weld Unit In Place:

Weld unit to truck or trailer only at

the four mounting brackets.

Inadequate support.

Supporting The Unit

Using Mounting Brackets

Do not use flexible mounts.

install3 6/05 803 274 / 200 864-A / 803 562

Содержание Big Blue 400 KX









































































Результаты поиска

Содержание Big Blue 400 KX

Отзывы:

Похожие инструкции для Big Blue 400 KX

Бренды по названию

Популярные бренды

Miller Electric Big Blue 400 KX, Руководство пользователя

Результаты поиска

Содержание Big Blue 400 KX

Отзывы:

Похожие инструкции для Big Blue 400 KX

Бренды по названию

Популярные бренды