Miele TXR 860 WP Скачать руководство пользователя

Страница: 92 / 100

Settings

Volume

The volume can be changed for the
buzzer that sounds when the dryer is
switched on and at the end of the
program. The volume of the buzzer
that sounds when a sensor button is
touched can also be changed.

Options

Finish tone

Keypad tone

Welcome Tone

It can be set to one of 7 different levels
or switched off altogether.

Display brightness

The brightness of the display can be
altered.

They can be set to one of 7 different
levels.

medium setting (factory setting)

“Display” off status

To save energy, the display and
sensor buttons will go out after
10 minutes and the

Start/Stop

button

will flash slowly. You can alter this
setting.

Options

Off

The display will remain on (i.e., it will
never go out).

The display will go out (after
10 minutes):

– if a program is not selected after

the dryer has been switched on

– during the current program

– at the end of a program

On -Not in current prog.

(Factory setting)
The display will go out (as described
above) but will remain on while the
program is running.

You can switch the display back on by
touching any sensor button.

Содержание TXR 860 WP





































































































Результаты поиска

Содержание TXR 860 WP

Отзывы:

Похожие инструкции для TXR 860 WP

Бренды по названию

Популярные бренды

Miele TXR 860 WP, Руководство по эксплуатации

Результаты поиска

Содержание TXR 860 WP

Отзывы:

Похожие инструкции для TXR 860 WP

Бренды по названию

Популярные бренды