Miele T 4882 C Скачать руководство пользователя страница 22

Страница: 22 / 60

Cottons Extra dry

Max. load: 5 kg*

Fabric type

Multi-layered fabrics, which would not be thoroughly dried using
the programme.

Notes

Do not dry jersey fabrics in the

Extra dry

programme as they

have a tendency to shrink.

Extras

Short or Low Temp.

Cottons

Max. load: 5 kg*

Fabric type

Single and multi-layered fabrics, e.g. mixed load of cotton fabrics
e.g. towelling, jerseywear, underwear.

Extras

Short or Low Temp.

Cottons Normal **

Max. load: 5 kg*

Fabric type

Load of similar cotton items, e.g. underwear, flannelette bed linen,
towelling.

Notes

If laundry is still too damp, then finish drying using the Warm air
programme and use the

Normal

+ programme next time.

Extras

Short or Low Temp.

Cottons Hand iron

Max. load: 5 kg*

Fabric type

Cottons and linen fabrics, e.g. table linen, bedlinen, starched
laundry etc.

Extras

Short or Low Temp.

Cottons Hand iron

Max. load: 5 kg*

Fabric type

Cottons and linen fabrics, e.g. table linen, bedlinen, starched
laundry etc.

Notes

If laundry is still too damp, then select

Hand iron

in the future.

Extras

Short or Low Temp.

Cottons Machine iron

Max. load: 5 kg*

Fabric type

Cotton and linen fabrics, including starched laundry for machine
ironing.

Notes

The laundry should be rolled up to prevent it from drying out
before it can be ironed.

Extras

Short or Low Temp.

* Weight of dry laundry
** Note for test institutes:
This programme setting without Extras should be used when testing according to
EN 61121 Standard.

Programme chart

Содержание T 4882 C





























































Результаты поиска

Содержание T 4882 C

Отзывы:

Похожие инструкции для T 4882 C

Бренды по названию

Популярные бренды

Miele T 4882 C, Руководство по эксплуатации

Результаты поиска

Содержание T 4882 C

Отзывы:

Похожие инструкции для T 4882 C

Бренды по названию

Популярные бренды