Miele T 4882 C Скачать руководство пользователя страница 2

Страница: 2 / 60

Disposal of the packing
material

The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.

Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!

Rather than just throwing these
materials away, please ensure they are
offered for recycling.

Disposal of your old appliance

Old appliances contain materials which
can be reclaimed or recycled. Please
contact your dealer, your local waste
collection centre or scrap merchant
about potential recycling schemes.

Ensure that the machine presents no
danger to children while being stored
for disposal.

Before throwing an old appliance
away unplug it and render the plug

useless. Cut off the cable directly
behind the appliance to prevent
misuse. This should be done by a
competent person.

Energy saving tips

Make sure that your laundry is
thoroughly spun before drying.

The higher the spin, the greater the
savings that can be made in energy
and time during drying.

Load according to the optimum
amount of laundry recommended for
the programme being used (see
Programme chart).

Underloading is uneconomical.
Overloading gives a poorer quality of
drying and may cause unnecessary
creasing.

To save energy and time:

– make sure the room in which the

dryer is located is well ventilated.

– Make sure the fluff filters are clean

before using the dryer.

Caring for the environment

Содержание T 4882 C





























































Результаты поиска

Содержание T 4882 C

Отзывы:

Похожие инструкции для T 4882 C

Бренды по названию

Популярные бренды

Miele T 4882 C, Руководство по эксплуатации

Результаты поиска

Содержание T 4882 C

Отзывы:

Похожие инструкции для T 4882 C

Бренды по названию

Популярные бренды