Miele T 4882 C Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 60

background image

Problem

Possible cause

Remedy

The programme
does not start and
the display is dark.

No obvious cause.

–

Have you followed correct
procedure for using the
machine?

–

Is the plug correctly inserted
in the socket and switched
on?

–

Is the appliance door closed
properly?

–

Has the fuse or circuit
breaker tripped?

The interior drum
lighting does not
come on.

The lighting switches off
automatically (to save
energy).

Switch the dryer off and then
on again.

The lamp needs
changing.

Change the lamp as described
at the end of this section.

The display is in a
different language.

A different language has
been selected in the
Settings - Language

J

menu.

Set the language you want.
The flag symbol will guide you.

The Start button
light will flash when
a programme is
being selected.

This is not a fault.

The flashing indicates that a
programme can be started.
After the programme has
started the flashing will change
to a constant light.

The display is dark
and the light ring
around the
multi-function
selector is not lit
up.

The Start button is
flashing slowly.

The display has switched
off automatically to save
energy (Stand-by mode).

The display and the
multi-function selector will light
up when one of the buttons is
pressed.

The lighting is defective if
it does not come on when
one of the buttons is
pressed.

Contact the Miele Service
Department.

Problem solving guide

37

«
...
35
36
37
38
39
...
»

Содержание T 4882 C





























































Отзывы:

Нет отзывов

Похожие инструкции для T 4882 C

Бренд: Dash Страницы: 25

HealthyCook HB4006

Бренд: Hamilton Beach Страницы: 8

Бренд: HAEGER Страницы: 24

Бренд: Hamilton Beach Страницы: 44

Бренд: V-ZUG Страницы: 32

Бренд: Mediclinics Страницы: 6

Бренд: Hotpoint Страницы: 16

Бренд: Fakir Страницы: 60

Бренд: AEG Страницы: 28

Бренд: Whirlpool Страницы: 16

Бренд: Whirlpool Страницы: 14

Бренд: Whirlpool Страницы: 12

Бренд: Whirlpool Страницы: 8

Бренд: Whirlpool Страницы: 16

Бренд: Whirlpool Страницы: 9

Бренд: Whirlpool Страницы: 15

Бренд: Whirlpool Страницы: 15

Бренд: Whirlpool Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды