Miele KWT6832SGS Скачать руководство пользователя | Manualshive

Страница: 28 / 72

background image

Door alarm

An alarm will sound if the door has
been left open for longer than 2
minutes. The three sensor buttons of
the wine storage zones flash on the
control panel. The alarm symbol

;

lights up in the display.

The alarm will stop when you close the
door. The three wine storage zone
sensors and the alarm symbol

;

will

go out.

Turning the door alarm off early

If the audio alarm bothers you, it can be
silenced.

^

Tap the sensor button to turn off the
door alarm.

The alarm will stop.
The three wine storage zone sensors
will flash and the alarm symbol

;

will

light up until you close the door.

If the audible tone does not sound in
the event of a door alarm, then the
audible tone has been turned off in
settings mode (see "Selecting
additional settings - Audible tones").

Temperature and door alarm

28

«
...
26
27
28
29
30
...
»

Содержание KWT6832SGS









































































Отзывы:

Нет отзывов

Похожие инструкции для KWT6832SGS

Бренд: Dometic Страницы: 6

Бренд: Brandt Страницы: 50

Бренд: Igloo Страницы: 9

Бренд: AGA marvel Страницы: 16

Бренд: Vinotemp Страницы: 11

Бренд: Vinotemp Страницы: 14

Бренд: Vinotemp Страницы: 16

WINE-MATE WM-1500LOWP

Бренд: Vinotemp Страницы: 24

Wine-Mate WM-1520SSW

Бренд: Vinotemp Страницы: 29

Wine-Mate 2520SSW-LA

Бренд: Vinotemp Страницы: 29

Wine-Mate WM-1500SSI

Бренд: Vinotemp Страницы: 30

Бренд: Vintec Страницы: 24

Бренд: Vintec Страницы: 24

Бренд: Premier Страницы: 8

Isotherm Divino The One

Бренд: Indel Webasto Marine Страницы: 232

Бренд: CellarCool Страницы: 28

Бренд: Cellartec Страницы: 28

Бренд: CellarCool Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды