Miele KWT6832SGS Скачать руководство пользователя | Manualshive

Страница: 59 / 72

background image

WARNING!
Danger of tilting! To avoid a hazard
due to instability of the appliance, it
must be secured in accordance with
the instructions.

Installation location

This appliance should not be installed
where it is exposed to direct sunlight or
directly adjacent to a heat-producing
appliance such as an oven or a
radiator. The room temperature should
not go above or below the climate
range for which the appliance is
designed. The higher the ambient
temperature of the room, the more
energy the appliance requires to
operate. The appliance should be
installed in a dry, well-ventilated room.

When installing the appliance, please
be aware:

– The electrical socket must be easily

accessible in an emergency, not
concealed behind the appliance.

– The plug and cord must not touch

the rear of the appliance as they
could be damaged by vibrations
from the appliance.

– Do not plug in other devices behind

this appliance.

Climate class

The appliance is designed for use
within a certain climate range (ambient
temperatures) and should not be used
outside this range. The climate range of
the appliance is stated on the data
plate inside the appliance.

Climate class

Room temperature

SN

N

ST

T

+50°F to +90°F

(+10°C to +32°C)

+60°F to +90°F

(+16°C to +32°C)

+60°F to +100°F

(+16°C to +38°C)

+100°F to 110°F

(+16°C to +43°C)

Ventilation

The appliance can be place with the
back side directly against the wall.
Make sure, however, that the ventilation
slits are not covered to ensure
adequate ventilation.
The ventilation slits must also be dusted
or cleaned on a regular basis.

Installation

^

Remove any cord clips from the back
of the appliance.

^

Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.

^

Carefully push the appliance into
position.

Installation

59

«
...
57
58
59
60
61
...
»

Содержание KWT6832SGS









































































Отзывы:

Нет отзывов

Похожие инструкции для KWT6832SGS

Бренд: Gaggenau Страницы: 48

Бренд: Avintage Страницы: 152

Бренд: Summit Professional Страницы: 12

Бренд: Caple Страницы: 32

Бренд: Elfa Страницы: 12

Бренд: Orbegozo Страницы: 25

Бренд: Awanti Страницы: 36

Бренд: Richelieu Страницы: 8

Бренд: Dacor Страницы: 6

Бренд: Kalorik Страницы: 24

HVA037-5S - 08-03

Бренд: Haier Страницы: 15

Бренд: Haier Страницы: 261

Бренд: Electrolux Страницы: 11

Бренд: Electrolux Страницы: 16

E24WC75HPS - Icon - Professional Series 48 Bottle Wine Cooler

Бренд: Electrolux Страницы: 19

Бренд: Electrolux Страницы: 13

Бренд: Electrolux Страницы: 18

Бренд: Electrolux Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды