Miele KWT6832SGS Скачать руководство пользователя

Страница: 62 / 72

The appliance is supplied right-hand
hinged. If left-hand hinging is required,
the hinges must be changed.

You will need the following tools for
changing the door hinging

Always change the door hinge with
the assistance of another person.
The glass door is heavy (approx.
66 lbs / 30 kg) and could break.

To protect the glass door and your floor
from damage during the change of the
door hinging,

lay a suitable ground covering on the
floor in front of the appliance.

Be careful not to damage the door
seal. If the door seal is damaged,
the appliance door may not close
properly and there will not be
enough refrigeration.

Removing the door

Open the appliance door as far as it
will go.

Lift the cover

at the bottom of the

appliance carefully using a slotted
screwdriver.

Place the red securing device

(supplied with the appliance) on the
soft-close mechanism

so that it

engages.

The restraining clip stops the hinge
from snapping shut. Do not remove the
clip until told to do so.

Push the pin

up and out.

Now the soft-close mechanism and the
appliance are no longer connected.

Adjusting the door hinge

Содержание KWT6832SGS









































































Результаты поиска

Содержание KWT6832SGS

Отзывы:

Похожие инструкции для KWT6832SGS

Бренды по названию

Популярные бренды

Miele KWT6832SGS, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание KWT6832SGS

Отзывы:

Похожие инструкции для KWT6832SGS

Бренды по названию

Популярные бренды