Miele KF 1803 Vi Скачать руководство пользователя страница 25

Страница: 25 / 88

Refrigerator section and
SmartFresh drawers

The refrigerator and SmartFresh
drawers defrost automatically.

During normal operation, condensate
and frost can form on the rear wall of
the refrigerator and drawers.
You do not need to remove this
build-up, it will defrost and evaporate
automatically with the heat generated
by the appliance.

Freezer section

The freezer section defrosts
automatically.

The moisture generated in the
appliance collects in the evaporator. It
is automatically defrosted and
dissipated by the condenser
periodically.

This automatic defrosting system
enables the freezer to remain
permanently ice-free, while ensuring
that the food stored in the freezer stays
frozen.

Automatic defrost

Содержание KF 1803 Vi

























































































Результаты поиска

Содержание KF 1803 Vi

Отзывы:

Похожие инструкции для KF 1803 Vi

Бренды по названию

Популярные бренды

Miele KF 1803 Vi, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание KF 1803 Vi

Отзывы:

Похожие инструкции для KF 1803 Vi

Бренды по названию

Популярные бренды