Miele KF 1803 Vi Скачать руководство пользователя страница 23

Страница: 23 / 88

When the SuperCool function is
activated, the appliance is cooled as
quickly as possible (to a factory-preset
temperature).

SuperCool

When used with the

refrigerator

the

SuperCool function is ideal for the rapid
cooling of drinks and refrigerating large
quantities of food.

When used with the

freezer

the

SuperCool function is ideal for freezing
large quantities of unfrozen food. The
function should be switched on

4-6

hours

before the fresh food is placed in

the freezer.
If the max. freezing capacity is used,

24 hours

are recommended.

This helps food to freeze quickly and
retain its nutrients, vitamins, flavor and
appearance.

Switching on SuperCool

Touch the sensor for the refrigerator
or freezer (as desired) so it turns
yellow.

Touch the SuperCool sensor button
so it turns yellow.

In the temperature display for the zone
selected, the new temperature setting
appears:

Refrigerator:

35°F (2°C)

Freezer:

-22°F (-30°C)

The temperature in the appliance now
begins to fall, with maximum cooling in
the zone selected.

Switching off SuperCool

The SuperCool function automatically
switches off after:
Refrigerator: approx. 6 hours
Freezer:

approx. 52 hours

The sensor button turns white, and the
appliance continues running at normal
power.

To save energy, the SuperCool function
can be switched off early, once the
food and/or drinks are sufficiently
chilled.

Touch the SuperCool sensor button
so that it turns white.

The temperature display for the zone
selected returns to the original
temperature setting.

The appliance now continues running
at normal power.

SuperCool

Содержание KF 1803 Vi

























































































Результаты поиска

Содержание KF 1803 Vi

Отзывы:

Похожие инструкции для KF 1803 Vi

Бренды по названию

Популярные бренды

Miele KF 1803 Vi, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание KF 1803 Vi

Отзывы:

Похожие инструкции для KF 1803 Vi

Бренды по названию

Популярные бренды