Miele KF 1803 Vi Скачать руководство пользователя страница 44

Страница: 44 / 88

Alarm / Indicator warnings

Issue

Possible fault

Solution

The alarm is ringing.

The appliance door(s)
have been open for
longer than 5 minutes.

Close the door(s).

The alarm is ringing and
the "alarm" indicator for
the door or temperature
is flashing.

The door is not closed.

Once the alarm condition
has been corrected, the
alarm will turn off and the
"alarm" indicator will stop
flashing.
The temperature indicator
will indicate the highest
temperature reached
during the alarm.

A large amount of food is
being frozen at the same
time.

There has been a power
failure.

The filter display is red.

This is a warning that the
water filter needs to be
changed soon.

Order replacement filters
from Miele.

The filter display is
flashing red.

The water filter needs to
be changed.

See "Exchanging the
water filter".

Frequently asked questions

Содержание KF 1803 Vi

























































































Результаты поиска

Содержание KF 1803 Vi

Отзывы:

Похожие инструкции для KF 1803 Vi

Бренды по названию

Популярные бренды

Miele KF 1803 Vi, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание KF 1803 Vi

Отзывы:

Похожие инструкции для KF 1803 Vi

Бренды по названию

Популярные бренды