Miele KF 1803 Vi Скачать руководство пользователя страница 16

Страница: 16 / 88

Temperature unit
(Fahrenheit/Celsius)

The temperature can be displayed in
degrees Fahrenheit (°F) or Celsius (°C).

Touch the access button "

" so it

turns yellow.

Touch the sensor button for the
refrigerator section so it turns yellow.

Note the position of the

button, but

do not touch.

Touch the access button "

" again so

it turns white.

Only the access button "

" is visible.

Place one finger on the position of
the

button and hold (the

button

will not be visible).

While holding down the

button,

press the access button "

" once.

Keep holding the

button down until

the following appears in the display
(approx. 5 seconds).

Tap the

button until

†

appears in

the display.

Touch the access button "

" to

confirm.

By touching the

button you can

select either Fahrenheit or Celsius for
the temperature display.

† 0

: Fahrenheit

† 1

: Celsius

†

–: return to menu

Touch the access button "

" to

confirm the setting.

Tap the

button until a

;

appears in

the display.

Touch the access button "

You have left the Custom settings
mode.

When you are in the Custom settings
mode the door alarm is turned off
automatically. Once the door is
closed it is reactivated.

Setting the temperature

Содержание KF 1803 Vi

























































































Результаты поиска

Содержание KF 1803 Vi

Отзывы:

Бренды по названию

Популярные бренды

Miele KF 1803 Vi, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание KF 1803 Vi

Отзывы:

Бренды по названию

Популярные бренды