Miele HoneyComb care T 4472 C Скачать руководство пользователя

Страница: 33 / 52

Problem

Possible cause

Remedy

The programme
stops and the
Anti-crease/Finish
indicator light
comes on.

appears in the
display. The buzzer
sounds.

This is not a fault.

The electronic unit has
recognised that there
is no laundry in the
drum and cancelled
the programme.

Drying individual
garments or items
which are already dry
can also cause the
programme to be
cancelled.

–

Use the Warm air programme
(timed drying) to dry
individual items.

–

The indicator light will go out
when you open and close the
door, if the dryer is switched
on.

The programme
stops and the
Machine iron or
Hand iron indicator
light flashes. The
buzzer sounds.

No obvious cause.

–

Switch the dryer off and then
on again.

–

Then start the programme
again.

If the programme stops again
and the indicator light flashes
again there is a fault. Contact the
Miele Service Department.

The time remaining
pauses. Bars

...

appear in the
display.

This is not a fault.

The drying process is
not yet complete.

The programme has taken
longer than was estimated at the
beginning.

The adjusted time remaining will
appear in the display after a
while.

The Locked
indicator starts
flashing after the
dryer has been
switched on. A
programme cannot
be started.

The system lock is
activated.

You will need to deactivate the
system lock before the dryer can
be used (see "Electronic system
lock").

Problem solving guide

Содержание HoneyComb care T 4472 C





















































Результаты поиска

Содержание HoneyComb care T 4472 C

Отзывы:

Похожие инструкции для HoneyComb care T 4472 C

Бренды по названию

Популярные бренды

Miele HoneyComb care T 4472 C, Руководство по эксплуатации

Результаты поиска

Содержание HoneyComb care T 4472 C

Отзывы:

Похожие инструкции для HoneyComb care T 4472 C

Бренды по названию

Популярные бренды