Miele HoneyComb care T 4472 C Скачать руководство пользователя страница 18

Страница: 18 / 52

Automatic

Max. load: 3 kg*

, Normal, Hand iron

Fabric type

Mixed load of cotton and minimum iron fabrics.

Extra option

Anti-crease

Cottons

Max. load: 6 kg*

Extra dry, , Normal**

Fabric type

Single and multi-layered cotton fabrics such as towelling,
jerseywear, underwear, flannelette bed linen.

Notes

–

Select the

Extra dry

drying level for multi-layered and very thick

fabrics.

–

Do not use the

Extra dry

drying level for jersey fabrics as they

have a tendency to shrink.

Extra options Low temperature (select this option for delicate fabrics with the

symbol on the care label), Short, Anti-crease

Hand iron

, Hand iron

**, Machine iron

Fabric type

Cottons or linen fabrics, e.g. table linen, bedlinen, starched
laundry.

Note

–

To prevent laundry from drying out it should be rolled up until
you are ready for ironing.

Extra options Low temperature (select this option for delicate fabrics with the

symbol on the care label), Short, Anti-crease

Synthetics

Max. load: 3 kg*

, Normal**, Hand iron

Fabric type

Minimum iron and delicate items made of cotton, synthetic or
blended fabrics, e.g. jumpers, skirts, trousers, table cloths, shirts,
blouses and evening wear with sequins and beading.

Note

Laundry remains relatively crease-free for easier ironing.

Extra options Low temperature (select this option for delicate fabrics with the

symbol on the care label), Short, Anti-crease

Weight of dry laundry

** Note for test institutes:
Use this programme without any Extra options when testing according to EN
61121 Standard.

Programme chart

Содержание HoneyComb care T 4472 C





















































Результаты поиска

Содержание HoneyComb care T 4472 C

Отзывы:

Похожие инструкции для HoneyComb care T 4472 C

Бренды по названию

Популярные бренды

Miele HoneyComb care T 4472 C, Руководство по эксплуатации

Результаты поиска

Содержание HoneyComb care T 4472 C

Отзывы:

Похожие инструкции для HoneyComb care T 4472 C

Бренды по названию

Популярные бренды