Miele HoneyComb care T 4472 C Скачать руководство пользователя | Manualshive

Страница: 7 / 52

background image

In the event of a fault or for
cleaning purposes, the machine is

only completely isolated from the
electiricty supply when:

– it is switched off at the wall socket

and the plug is withdrawn, or

– it is switched off at the mains, or

– the mains fuse is withdrawn.

Operation

This equipment may only be used
in mobile installations such as

ships, caravans, aircraft etc. if a risk
assessment of the installation has been
carried out by a suitably qualified
engineer.

The dryer must not be used without
the fluff filters in place or if the fluff

filters are damaged in any way.

The fluff filters must be thoroughly
dried after cleaning. If they are still

damp or wet when replaced there is a
risk of faults occurring when the
machine is used.

The dryer must not be used without
the condenser unit in place.

Do not install the machine in a
room where there is a risk of frost

occurring. At temperatures around
freezing point the machine may not be
able to operate properly.
There is a risk of damage if the
condensed water is allowed to freeze in
the pump, hoses and / or condensed
water container.
The ambient room temperature should
be b2°C and +35°C.

If the water is drained externally
through the drain hose instead of

being collected in the condensed water
container, make sure the drain hose is
securely attached if you hang it in a
sink or basin to avoid the hose slipping
and the water causing damage.

Condensed water is not drinking
water. It can cause health

problems in both people and animals.

Always keep the area around the
machine free of dust and fluff. Dust

drawn into the machine can, over time,
cause blockages in the condenser unit.

Warning and Safety instructions

7

«
...
5
6
7
8
9
...
»

Содержание HoneyComb care T 4472 C





















































Отзывы:

Нет отзывов

Похожие инструкции для HoneyComb care T 4472 C

Бренд: UFESA Страницы: 62

Бренд: Lotus Страницы: 20

Бренд: Presto Страницы: 6

Бренд: Electrolux Страницы: 40

Бренд: Electrolux Страницы: 24

Бренд: Electrolux Страницы: 44

Бренд: Electrolux Страницы: 36

Бренд: Electrolux Страницы: 44

Бренд: Electrolux Страницы: 48

Бренд: Electrolux Страницы: 52

Бренд: Electrolux Страницы: 52

Бренд: Electrolux Страницы: 80

Бренд: Electrolux Страницы: 36

Бренд: Electrolux Страницы: 47

Бренд: Electrolux Страницы: 32

Бренд: Electrolux Страницы: 48

Бренд: Electrolux Страницы: 84

Бренд: Electrolux Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды