manualshive.com logo in svg

Midtronics GRX-3080 JLR EU, Инструкция по эксплуатации

Поделиться
Скачать
Midtronics GRX-3080 JLR EU Скачать руководство пользователя страница 23

GRX-3080 JLR EU STANDALONE

Midtronics B.V.     Hoofdveste 6     Houten NL

www.midtronics.com

23

Chapter 6: PDI / Storage

Completing a Charge Session

The charge session is complete when the proper amount 

of charge is put back into the battery or the remaining 

estimated time to charge counts down to zero. 

  IMPORTANT: When you start a new test, the last bat-

tery test in memory will be overwritten. Remember 

to record or print the results if you need to retain 

them.

Diagnostic Charging Results

Use the UP (

) or DOWN (

) ARROW keys to scroll to each 

screen. To print, press the PRINT soft key.

State-of-Health (SOH)

A factor that affects a battery’s ability to crank an engine is its 

actual condition or State-of-Health (SOH). It is a measure of 

the battery’s condition relative to a fresh battery. 
A State-of-Health problem is most often the result of normal 

wear-out mechanisms, which are dependant on vehicle 

needs, climate, and operating conditions. This results in 

irreversible physical and chemical changes until eventually 

the battery can no longer hold a charge and supply the 

power necessary to start the car and provide auxiliary power 

to the electrical system.
As the battery approaches end of life, its deterioration 

accelerates, until it finally fails to start the vehicle.  Before 

failing, the battery may start the vehicle under normal 

conditions but may not be able to operate in more extreme 

conditions. Extreme heat or cold could expose a weak 

battery and cause it to fail.

Results Screen

Battery 

decision:
‘GOOD 

BATTERY’

Voltage
Measured 

CCA
Recharged Ah
Total charging 

time

 Battery Decisions: Diagnostic Charge

Battery Decision

Recommended Action

GOOD BATTERY Return the battery to service.

REPLACE 

BATTERY

A REPLACE BATTERY result may also 

mean a poor connection between the 

battery cables and the battery. After 

disconnecting the battery cables, retest 

the battery using the out-of-vehicle test 

before replacing it.

BAD CELL–

REPLACE 

Replace the battery. This decision 

indicates a bad cell within the battery.

FROZEN 

BATTERY

The GRX may display FROZEN 

BATTERY. Warm the battery and retest. 

Never charge a frozen battery. Gases 

may form, cracking the case, and 

leak battery acid.

Содержание GRX-3080 JLR EU



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды