manualshive.com logo in svg

Midtronics GRX-3080 JLR EU, Инструкция по эксплуатации

Поделиться
Скачать
Midtronics GRX-3080 JLR EU Скачать руководство пользователя страница 10

GRX-3080 JLR EU STANDALONE

Midtronics B.V.     Hoofdveste 6     Houten NL

www.midtronics.com

10

Chapter 1: Before You Begin

Assembly of the GRX-3080

The GRX-3080 Battery Diagnostic Station is shipped in two 

pieces: The cart and the charge engine.

Assemble the Cart

1.  For easy shipping the cart is shipped in a partial as-

sembled way. Please refer to the Instruction sheet that 

comes with the package on how to safely assemble.

2.  Mount the charge engine on the cart and fix it with a 

bolt at the back. Tighten the bolt securely.

Attaching the Charger Cables

The two connectors for the charger cables are located on 

the back of the unit. Three screws are included to secure the 

cables. To attach the cables:

1.  Plug the small connector into the small socket (A) on the 

back of the unit.

2.  Plug the large connector (B) into the large socket while 

placing the protective cover (C) against the back of the 

unit.

3.  Center the three holes in mounting bracket over the 

bolts, and lower the bracket onto the charger. Reinstall 

the hardware in this order: the flat washer first, the lock 

washer next, and the hex nut last. Tighten the nuts se-

curely.

4.  Insert the screws through the holes in the cover and and 

securely tighten the screws.

The installation is now complete.

Attaching the Power Cord

Plug in the power cord on the back of the unit.

Connecting to AC Power

Plug the charger into a dedicated, grounded nominal 16-

amp or higher AC outlet. Press the power switch to the 

ON

 

position.

A

B

C

Содержание GRX-3080 JLR EU



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды