background image

Oasis On-off 

 

DM12-01.01.09en

 

4  

Service 

manual 

 

For installation, always contact the dealer or an authorized service center. 

 

Do not install the product on a defective installation stand. 

 

Be sure the installation area does not deteriorate with age. 

If the base collapses, the air conditioner could fall with it, causing property damage, product failure, 

and personal injury. 

 

Do not let the air conditioner run for a long time when the humidity is very high and a 

door or a window is left open. 

 

Take care to ensure that power cable could not be pulled out or damaged during 

operation. 

There is risk of fire or electric shock. 

 

Do not place anything on the power cable. 

There is risk of fire or electric shock. 

 

Do not plug or unplug the power supply plug during operation. 

There is risk of fire or electric shock. 

 

Do not touch (operation) the product with wet hands. 

 

Do not place a heater or other appliance near the power cable. 

There is risk of fire and electric shock. 

 

Do not allow water to run into electrical parts. 

It may cause fire, failure of the product, or electric shock. 

 

Do not store or use flammable gas or combustible near the product. 

There is risk of fire or failure of product. 

 

Do not use the product in a tightly closed space for a long time. 

Oxygen deficiency could occur. 

 

When flammable gas leaks, turn off the gas and open a window for ventilation before 

turn the product on. 

 

If strange sounds or smoke comes from product, turn the breaker off or disconnect the 

power supply cable. 

There is risk of electric shock or fire. 

 

Stop operation and close the window in storm or hurricane. If possible, remove the 

product from the window before the hurricane arrives. 

There is risk of property damage, failure of product, or electric shock. 

Содержание MO11M-09HN1
























































Отзывы: