CLI Commands
36
098-00777-000 Rev. A
latitude : 0.000000
longitude : 0.000000
altitude : 0.000000
hdop : 0.000000
fix-quality : 0
pdop : 0.000000
op-mode : 1
GNSS Status :
Current Status : disqualified
Current Reference Status : fault
Current Position Status : surveying
Current Antenna Position :
Latitude : N00:00:00.00
Longitude : E000:00:00.00
Height : 0.00
Example 4:
S80> show gnss monitor-info
Response 4:
hw-aStatus: 1
hw-flags : 0x00
hw-jamInd: 83
io-rxBytes: 15140
io-txBytes: 8184404
io-parityErrs: 0
io-framingErrs: 0
io-overrunErrs: 0
survey-in-duration : 7754
survey-in-observation : 0
survey-in-postion-valid : 0
survey-in-progress : 1
pdop : 99.989998
fixType : 0,NO-Fix
numSv : 0
set gnss
This command allows the user to set the cable delay and the elevation mask. the angle below which the
satellites are not used by the system. It allows the user set the track mode for GPS only (disable) or GPS
+ GLONASS (enable).
This command also allows the user to set the position mode to auto (default) for stationary or dynamic. At
startup, the S80 is in survey mode. For Auto position mode, the S80 fixes its position at the stationary
location. For dynamic positioning mode, the S80 will "survey always" but the user can set for Automotive
or Sea. (The "Air" setting is for future use and not currently supported.)
Command Syntax:
•
To set the GNSS state:
set gnss state {enable | disable}
Note:
If GNSS is disabled, the S80 still shows satellites tracked but doesn’t provide valid time and freq.
•
To set the GNSS elevation mask:
set gnss mask {5 to 60}
Note:
SyncServer S80
•
To set the GNSS cable delay value:
set gnss cable-delay {0 to 9999}
•
To set the GNSS position mode:
Содержание SyncServer S80
