Configuration
52
098-00777-000 Rev. A
Establishing a Connection to the S80
To set up and manage the S80 with a terminal or a computer with terminal emulation, you must establish
an SSH connection.
Note:
The S80 default IP address is 192.168.100.11, the subnet mask is 255.255.255.0, and the gateway
address is 0.0.0.0 (no gateway).
1. Establish an SSH connection from your computer to the IP address assigned to the S80.
2. Type your user name and press Enter.
3. Type your assigned password and press Enter. The system prompt appears.
Configuring the IP Address
The S80 supports static as well as dynamically allocated IP addresses on the Ethernet port. The
dynamically allocated address requires a connection to a DHCP server. When provisioning the unit for
static IP address, you can set the Host address, Mask address, and Gateway address, or you can set the
addresses to the factory default.
DHCP Mode
You can either enable or disable DHCP mode, Use the following procedure to configure the S80 to
enable DHCP on the MGMT port.
Example
1. Login at the Admin or Config-user level (see
2. Type
set ip ipv4 address-mode dhcp
and press
Enter
.
Caution:
If you set the mode to DHCP you should have a way to find out the assigned IP address. There is
no way to get it from the S80 unit unless you're using LLDP.
Static IP Mode
Use the following procedures to configure the S80 Ethernet parameters (IP Address, Subnet Mask or
Prefix, and Gateway Address). The IT department or site administrator for your location can recommend
specific addresses for these parameters. Use the dotted decimal format xxx.xxx.xxx.xxx to enter an IPv4
address parameters with the following commands:
Example - IPv4
1. Type
set ip ipv4 address-mode static
and press Enter.
2. Type
set ip ipv4 ip-address address 192.168.0.10 netmask 255.255.255.0 gateway
192.168.0.254
and press Enter.
3. Type
set ip ipv4 state restart
and press Enter.
Example - IPv6
1. Type
set ip ipv6 address-mode static
and press Enter.
2. Type
set ip ipv6 ip-address address 2001:db8:1234::2 prefix 64 gateway
2001:db8::1
and press Enter.
3. Type
set ip ipv6 state restart
and press Enter.
Содержание SyncServer S80
