Microplex SOLID F44 Скачать руководство пользователя страница 17

Страница: 17 / 167

Preface

About this Manual

This manual covers the printer

SOLID F44

and the

intelligent Paper Stacker

iPS

F44

The structure of this manual is such that the operator is led step-by-step through the

various procedures. Starting with unpacking and installation of the consumables it

moves on to setting-up configuration parameters and ends with the mounting of

options.
The manual is divided into the following chapters:

1. Installing the Printer and intelligent Paper Stacker

This chapter describes the unpacking and setting up the printer and the installation of

the print cartridge (consumables) are explained. After completing this chapter, the

default printer in its fully operational and tested, but have not yet configured

particularly, that the connection to the computer and set the various options have not

already done.

2. Operating the Printer

This chapter discusses in great detail the operation of the control panel, all menu

functions, and the general operation of the menu. General status messages are

also described.

Configuring the printer

Get the handling with the profiles is explained, it is described how the printer is set,

so it can communicate with the appropriate systems environment. In this chapter

you will find the menu tree. Then, the menu items are explained in a table.

4. Explanation of Individual Menu Items

In this chapter are the individual menu items are explained in detail.

5. Maintenance

This chapter describes the cleaning and maintenance of the printer. Also, the

procedure is described in a paper jam, and the replacement of consumables that

must be done by the user.

6. Trouble Shooting and Diagnostics

This chapter covers information on troubleshooting and repairing simple problems.

All error messages with corresponding instructions to the user described in tabular

form.

Содержание SOLID F44








































































































































































Результаты поиска

Содержание SOLID F44

Отзывы:

Похожие инструкции для SOLID F44

Бренды по названию

Популярные бренды

Microplex SOLID F44, Руководство пользователя

Результаты поиска

Содержание SOLID F44

Отзывы:

Похожие инструкции для SOLID F44

Бренды по названию

Популярные бренды