Microlife aponorm Basis, Руководство пользователя

Страница: 15 / 103

15 EN
aponorm
®
Basis
Using rechargeable batteries
You can also operate this instrument using rechargeable batteries.
10. Using a Mains Adapter
You can operate this instrument using the Microlife mains adapter
(DC 6V, 600mA).
When the mains adapter is connected, no battery current is
consumed.
)
Please use only type «NiMH» reusable batteries!
)
The batteries must be removed and recharged, if the battery
symbol (battery flat) appears! They must not remain inside
the instrument, as they may become damaged (total
discharge as a result of low use of the instrument, even
when switched off).
)
Always remove the rechargeable batteries, if you do not
intend to use the instrument for a week or more!
)
The batteries can NOT be charged in the blood pressure
monitor! Recharge these batteries in an external charger
and observe the information regarding charging, care and
durability!
)
Use only the Microlife mains adapter available as an orig-
inal accessory appropriate for your supply voltage, e.g. the
«Microlife 230V adapter».
)
Ensure that neither mains adapter nor cable are not
damaged.
1. Plug the adapter cable into the mains adapter socket
5
in the
blood pressure monitor.
2. Plug the adapter plug into the wall socket.
You can operate this instrument using the aponorm ® by microlife
adapter (DC 6V, 600mA).
Use only the aponorm
®
by microlife mains adapter avai-
lable as an original accessory appropriate for your supply
voltage, e.g. the «aponorm
®
by microlife 230V adapter».
7.
11. Error Messages
If an error occurs during the measurement, the measurement is
interrupted and an error message, e.g. «
ERR 3 », is displayed.
* Please consult your doctor, if this or any other problem occurs
repeatedly.
Error Description Potential cause and remedy
« ERR 1 » Signal too
weak
The pulse signals on the cuff are too
weak. Re-position the cuff and repeat
the measurement.*
« ERR 2 » Error signal During the measurement, error signals
were detected by the cuff, caused for
instance by movement or muscle
tension. Repeat the measurement,
keeping your arm still.
« ERR 3 » No pressure
in the cuff
An adequate pressure cannot be gener-
ated in the cuff. A leak may have
occurred. Check that the cuff is correctly
connected and is not too loose. Replace
the batteries if necessary. Repeat the
measurement.
« ERR 5 » Abnormal
result
The measuring signals are inaccurate
and no result can therefore be displayed.
Read through the checklist for
performing reliable measurements and
then repeat the measurement.*
« ERR 6 » MAM Mode There were too many errors during the
measurement in MAM mode, making it
impossible to obtain a final result. Read
through the checklist for performing reli-
able measurements and then repeat the
measurement.*
« HI » Pulse or cuff
pressure too
high The pressure in the cuff is too high (over
300 mmHg) OR the pulse is too high (over
200 beats per minute). Relax for 5
minutes and repeat the measurement.*
« LO » Pulse too
low The pulse is too low (less than 40 beats
per minute). Repeat the measurement.*
)
If you think the results are unusual, please read through the
information in «Section 1.» carefully.
8.
* Please consult your doctor, if this or any other problem occurs
repeatedly.
« HI » Pulse or cuff
pressure too
high The pressure in the cuff is too high (over
300 mmHg) OR the pulse is too high (over
200 beats per minute). Relax for 5
minutes and repeat the measurement.*
« LO » Pulse too
low The pulse is too low (less than 40 beats
per minute). Repeat the measurement.*
)
If you think the results are unusual, please read through the
information in «Section 1.» carefully.