Microhard Systems n2420 Скачать руководство пользователя страница 57

Страница: 57 / 93

6.0 Configuration

Identification

The I command returns information about the Nano.

Product Code

Issue ROM Check (OK or ERROR)

Product Identification (Firmware Version)

Firmware Date

Firmware Copyright

Firmware Time

Serial Number

255

Factory-Configured Options listing

Advanced Spectrum Analyzer

The Advanced Spectrum Analyzer feature provides for a very detailed analysis of a

particular area of the radio frequency spectrum within which the Nano operates.

The specific start (of scan) and stop frequencies, along with step (increment) size and

dwell (on frequency) time are user-definable.

Following is the format for the ATN command:

In Command Mode

ATN F

start

stop

S D[Enter]

where

start

= start frequency in MHz (including 0-6 decimal places)

stop

= stop frequency in MHz (including 0-6 decimal places)

= step increment in kHz (from 1-1000)

= dwell time in ms (from 1-1000)

Example:

ATN 905.250 908.500750 25 100

Note: Be sure to enter spaces as shown in the format detailed above.

Online Mode

Upon completion of tasks being done with the modem in Command Mode, invoking

this command will place the modem back ‘online’ (into Data Mode).

Содержание n2420






























































































Результаты поиска

Содержание n2420

Отзывы:

Похожие инструкции для n2420

Бренды по названию

Популярные бренды

Microhard Systems n2420, Руководство по эксплуатации

Результаты поиска

Содержание n2420

Отзывы:

Похожие инструкции для n2420

Бренды по названию

Популярные бренды