Microhard Systems n2420 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 93

background image

© Microhard Systems Inc.

4

Important User Information (continued)

Regulatory Requirements

To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance

of 23cm or more should be maintained between the antenna of this device and persons during

device operation. To ensure compliance, operations at closer than this distance is not

recommended. The antenna being used for this transmitter must not be co-located in conjunction

with any other antenna or transmitter.

This device can only be used with Antennas listed in Appendix C/D. Please contact Microhard

Systems Inc. if you need more information or would like to order an antenna.

WARNING

MAXIMUM EIRP

FCC Regulations allow up to 36dBm Effective Isotropic Radiated Power (EIRP). Therefore, the

sum of the transmitted power (in dBm), the cabling loss and the antenna gain cannot exceed

36dBm.

WARNING

EQUIPMENT LABELING

This device has been modularly approved. The manufacturer, product name, and FCC and

Industry Canada identifiers of this product must appear on the outside label of the end-user

equipment.

WARNING

FCCID: NS908P24
IC: 3143A-08P24

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and  (2)  this  device  must  accept  any  interference
received  including  interference  that  may  cause
undesired operation.

Please Note: These are only sample labels; different products contain different identifiers. The

actual identifiers should be seen on your devices if applicable.

SAMPLE LABEL REQUIREMENT:

For n920S/F/BD Nano Series OEM

For n920T Nano Series OEM

FCCID: NS908P25
IC: 3143A-08P25

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and  (2)  this  device  must  accept  any  interference
received  including  interference  that  may  cause
undesired operation.

FCCID: NS911P31
IC: 3143A-11P31

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and  (2)  this  device  must  accept  any  interference
received  including  interference  that  may  cause
undesired operation.

For n2420

n920X2

FCCID: NS9N920X2
IC: 3143A-N920X2

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and  (2)  this  device  must  accept  any  interference
received  including  interference  that  may  cause
undesired operation.

«
...
2
3
4
5
6
...
»

Содержание n2420






























































































Отзывы:

Нет отзывов

Похожие инструкции для n2420

Бренд: S&C Страницы: 40

Бренд: S&C Страницы: 34

Бренд: Eaton Страницы: 16

Бренд: Hardi Страницы: 2

Бренд: YASKAWA Страницы: 64

Бренд: V2 Страницы: 3

Бренд: Gardena Страницы: 17

Бренд: SAFI Страницы: 18

Бренд: Badger Meter Страницы: 2

Бренд: Badger Meter Страницы: 48

BadgerTouch HREBT

Бренд: Badger Meter Страницы: 12

Бренд: Badger Meter Страницы: 16

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Бренд: Gate Motors Страницы: 6

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

Бренд: Veeder-Root Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды