manualshive.com logo in svg

Microchip Technology PIC16F716, Техническое описание

Поделиться
Скачать
Microchip Technology PIC16F716 Скачать руководство пользователя страница 82

PIC16F716

DS41206A-page 80

Preliminary

 2003 Microchip Technology Inc.

MOVWF

Move W to f

Syntax:

[ label ]    MOVWF     f

Operands:

0 

≤

 f 

≤

 127

Operation:

(W) 

→

 (f)

Status Affected:

None

Encoding:

00

0000

1fff

ffff

Description:

Move data from W register to 
register ‘f’.

Words:

1

Cycles:

1

Example

MOVWF

REG1

Before Instruction

REG1 = 0xFF
W

= 0x4F

After Instruction

REG1 = 0x4F
W

= 0x4F

NOP

No Operation

Syntax:

[ label ]    NOP

Operands:

None

Operation:

No operation

Status Affected:

None

Encoding:

00

0000

0xx0

0000

Description:

No operation.

Words:

1

Cycles:

1

Example

NOP

OPTION

Load Option Register

Syntax:

[ label ]    OPTION

Operands:

None

Operation:

(W) 

→

 OPTION

Status Affected:

None

Encoding:

00

0000

0110

0010

Description:

The contents of the W register are 
loaded in the OPTION register. 
This instruction is supported for 
code compatibility with PIC16C5X 
products. Since OPTION is a 
readable/writable register, the 
user can directly address it. Using 
only register instruction such as 

MOVWF.

Words:

1

Cycles:

1

Example

To maintain upward compatibil-
ity with future PICmicro

®

 

products, do not use this 
instruction.

RETFIE

Return from Interrupt

Syntax:

[ label ]    RETFIE

Operands:

None

Operation:

TOS 

→

 PC,

1 

→

 GIE

Status Affected:

None

Encoding:

00

0000

0000

1001

Description:

Return from Interrupt. Stack is 
POPed and Top of Stack (TOS) 
is loaded in the PC. Interrupts 
are enabled by setting Global 
Interrupt Enable bit, GIE 
(INTCON<7>). This is a 
two-cycle instruction.

Words:

1

Cycles:

2

Example

RETFIE

After Interrupt

PC = TOS
GIE = 1

Содержание PIC16F716































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды