manualshive.com logo in svg

Microchip Technology PIC16F716, Техническое описание

Поделиться
Скачать
Microchip Technology PIC16F716 Скачать руководство пользователя страница 27

 2003 Microchip Technology Inc.

Preliminary

DS41206A-page 25

PIC16F716

FIGURE 3-10:

BLOCK DIAGRAM OF RB7/P1D PIN 

TABLE 3-3:

PORTB FUNCTIONS

Name

Bit#

Buffer Function

RB0/INT/
ECCPAS2

bit 0

TTL/ST

(1)

Input/output pin or external interrupt input. Internal software 
programmable weak pull-up. ECCP auto-shutdown input.

RB1/T1OS0/
T1CKI

bit 1

TTL/ST

(1)

Input/output pin or Timer1 oscillator output, or Timer1 clock input. Internal 
software programmable weak pull-up. See Section 5.0 “Timer1 Module” 
for detailed operation.

RB2/T1OSI

bit 2

TTL/XTAL

Input/output pin or Timer1 oscillator input. Internal software programmable 
weak pull-up. See Section 5.0 “Timer1 Module” for detailed operation.

RB3/CCP1/
P1A

bit 3

TTL/ST

(1)

Input/output pin or Capture1 input, or Compare1 output, or PWM A output. 
Internal software programmable weak pull-up. See CCP1 section for 
detailed operation.

RB4/
ECCPAS0

bit 4

TTL

Input/output pin (with interrupt-on-change). Internal software programmable 
weak pull-up. ECCP auto-shutdown input.

RB5/P1B

bit 5

TTL

Input/output pin (with interrupt-on-change). Internal software programmable 
weak pull-up. PWM B output.

RB6/P1C

bit 6

TTL/ST

(2)

Input/output pin (with interrupt-on-change). Internal software programmable 
weak pull-up. PWM C output. Serial programming clock.

RB7/P1D

bit 7

TTL/ST

(2)

Input/output pin (with interrupt-on-change). Internal software programmable 
weak pull-up. PWM D output. Serial programming data.

Legend: TTL = TTL input, ST = Schmitt Trigger input, XTAL = Crystal Oscillator input
Note 1:

This buffer is a Schmitt Trigger input when configured as the external interrupt or peripheral input.

2:

This buffer is a Schmitt Trigger input when used in Serial Programming mode.

Data Latch

From other

RBPU

(1)

P

V

DD

Q

D

CK

Q

D

CK

Q

D

EN

Q

D

EN

DATA BUS

WR PORTB

WR TRISB

Set RBIF

TRIS Latch

RD TRISB

RD PORTB

RB7:RB4 pins

weak
pull-up

RD PORTB

Latch

TTL
Buffer

Q3

Q1

Note

1:

To enable weak pull-ups, 
set the appropriate TRIS 
bit(s) and clear the RBPU 
bit (OPTION_REG<7>).

V

SS

 V

DD

RB7/P1D

0

1

Q

PWMD(P1D) Enable

PWMD(P1D) Data out

PWMD(P1D) Auto-shutdown tri-state

ST
Buffer

ICSPD - In circuit serial programming data input

Содержание PIC16F716































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды