micro-trak Calc-An-Acre II Скачать руководство пользователя

Страница: 8 / 30

Installation (cont.)

Electrical Installation

This section explains how to hook-up your Calc-An-Acre II to a 12VDC power connection.

The Calc-An-Acre II must be connected to a 12VDC negative ground electrical system.

ROUTING HARNESS AND CABLING

Avoid ar eas where the ca ble may be sub ject ed to abra sion or exces sive heat.

POWER CONNECTION

Locate the power cable lead on the Calc-An-Acre II harness and route to a sw12VDC source. At tach the BLACK wire

to ground. Connect the RED wire to positive terminal. If using an unprotected circuit as +12VDC source, add a 2A inline fuse

(not included in kit.)

Alternately, the Calc-An-Acre II can be powered directly from the battery along with a power switch (not included in kit.)

Note: Ensure clean metal-to-metal con tact from wiring to terminals.

Calc-An-Acre II is equipped with a non-volatile memory which does not re quire a con stant supply of power to retain daily

totals or calibration val ues.

WIRING HARNESS ORIENTATION

Wiring with multiple branches must be installed so that the individual wires point downward, as shown. This will protect the

internal connections from exposure to liquid chemicals.

WRONG

RIGHT

Example of power connection to switched ignition source

Black to Ground

Attach RED wire to

terminal or lead that is

“hot” with ignition on.

2-amp in-line fuse required (Not Provided) for unprotected circuits

FUSEHOLDER

Содержание Calc-An-Acre II































Результаты поиска

Содержание Calc-An-Acre II

Отзывы:

Похожие инструкции для Calc-An-Acre II

Бренды по названию

Популярные бренды

micro-trak Calc-An-Acre II, Справочное руководство

Результаты поиска

Содержание Calc-An-Acre II

Отзывы:

Похожие инструкции для Calc-An-Acre II

Бренды по названию

Популярные бренды