micro-trak Calc-An-Acre II Скачать руководство пользователя

Страница: 26 / 30

NOTE: This is an optional method generally used on

pickups or custom vehicles. It may also be nec es sary on

any other vehicles where ac cess to the wheels is

lim it ed.

This in stal la tion requires a fine tuning procedure,

see page 16.

Determine the best location for the magnets on drive shaft

according to which is the most practical spot to attach

sensor mounting bracket. This position should be no more

than 12” (.30 meters) behind the front U-joint. For best

results, mount “L” bracket to transmission and mount

magnets on drive shaft as close to transmission as pos si ble.

This will en sure prop er alignment if drive train shifts under

heavy loading.
Two magnets are required for proper Hall-effect speed

sensor operation. Position them exactly opposite each other

(180 de grees apart). The polarity (north and south poles)

detect ed by the Hall-effect speed sen sor must alternate as

the shaft is turned. The magnets provided by Micro-Trak are

marked with a dashed line on the SOUTH pole side of the

magnet.

• Attach magnets onto drive shaft, one NORTH pole side

out and the other SOUTH (dashed) pole side out, by

wrapping ca ble tie around shaft and magnets. Position

each mag net so that its longest dimension moves in

the di rec tion of rotation. Pull cable tie tight and trim

off excess. An adjust able, non-magnetic (stain less steel)

band clamp may also be substituted.

• Attach sensor bracket to vehicle transmission.

See

Illustration below.

Use either the short or long end of

the brack et as a base.

• Turn one locking nut onto threaded sensor and in sert

sensor into large hole selected on mount ing brack et.

Turn on remaining locking nut. Set sensor to proper

distance from magnets (1/4” to 1/2”, or 6mm to 13mm).

When distance is set, tight en nuts to lock sensor in

place.

• Secure sensor cable to frame with cable ties. Place first

tie as close to sensor assembly as possible.

See SPEED CAL on page 16.

Appendix A

(cont)

Optional Speed Sensor Mounting on Drive Shaft

Transmission/ Transfer Case

Drive Shaft

Magnets Positioned

180° Apart

¼” to ½”

(6mm to 13mm)

Air Gap

Sensor Body

(Green)

Fasten sensor bracket with
existing transmission bolts

or secure with clamps.

Содержание Calc-An-Acre II































Результаты поиска

Содержание Calc-An-Acre II

Отзывы:

Похожие инструкции для Calc-An-Acre II

Бренды по названию

Популярные бренды

micro-trak Calc-An-Acre II, Справочное руководство

Результаты поиска

Содержание Calc-An-Acre II

Отзывы:

Похожие инструкции для Calc-An-Acre II

Бренды по названию

Популярные бренды