manualshive.com logo in svg

micro-trak Calc-An-Acre II, Справочное руководство

Поделиться
Скачать
micro-trak Calc-An-Acre II Скачать руководство пользователя страница 21

21

All Calc-An-Acre II consoles are tested prior to packaging, 

so unless there has been damage in shipment you can be 

confident that everything will be operational when you 

receive it. 
However, if you do encounter a problem that appears to be 

related to equipment failure, 

PLEASE DO NOT OPEN THE 

CONSOLE.

   Your system is protected by a warranty, and   

Micro-Trak will gladly correct any defect.
Problems can be the result of mistakes in installation 

or operation. Before returning any parts for service, 

carefully check your installation and review the operating 

instructions.  

For easy-to-follow guidelines, refer to the 

troubleshooting section which follows.

CONSOLE APPEARS DEAD

Using your test light, check for 12 volts at the power source. 

Also check for damaged power cable or reversed terminals. 

(Console requires 12 volts for proper operation). 

SPEED IS ALWAYS ZERO OR ERRATIC

Check for properly calibrated speed cal number.
Review speed sensor installation. Check for proper 

mounting, alignment and spacing of speed sensor in 

relationship to magnet assembly. Make sure magnet 

polarities are alternated.  Also check cable for breaks or 

incomplete connection. 

For more suggestions on solutions to speed problems, see 

Hall-effect sensors and console inputs on pages 23.

DISTANCE COUNT IS INACCURATE

Speed cal number was incorrectly calculated or entered. 

Review calibration, re-adjust and test.

AREA COUNT IS INACCURATE

Working width or wheel circumference was measured  

incorrectly, or speed cal number was  incorrectly calculated 

or entered. Go back through the original procedures, make 

changes, and test for acre (hectare) count again. Verify 

accuracy with formula:
Acres = Distance x Width in feet/43560

Hectares = Distance x Width in meters/10,000

Thousands of square feet = Distance x Width in feet/1000

CONSOLE IS ERRATIC IN OPERATION

If you have a two-way radio, it may be mounted too close 

to the console.  Keep all Calc-An-Acre II cables away from 

the radio, its antenna and power cable.
Ignition wires may be causing the console to malfunction.  

Keep Calc-An-Acre II cables away from ignition wires, or 

install ignition suppressor.
Reroute all cable away from electric solenoids, air 

conditioning clutches and similar equipment.

DISPLAYED MEASUREMENTS DO NOT MAKE SENSE

The console may be in the incorrect measurement mode 

(English or metric). 

See page 15 for instructions

.

DISPLAY READS “OFL”

DISTANCE, AREA, TOTAL HOURS and SUB HOURS counters 

read OFL when they have exceeded their maximum count. 

Reset to zero to resume counting.

Troubleshooting 

(cont)

General

Содержание Calc-An-Acre II































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды