micro-trak Calc-An-Acre II Скачать руководство пользователя

Страница: 23 / 30

12v

If there is no response from any of the following tests, refer

to the main wiring diagram to locate the next connector

in line to ward the con sole and repeat the test at that con-

nec tor. If there is a response at that connector, the problem

may be in the cable between the two connectors (or the

con nec tors themselves).

SPEED INPUT

Turn rotary switch to speed po si tion and dis con nect the

speed sensor (yel low tie) from the main harness. Check

harness speed connector for 12V between pins B (wh)

and C (blk) and 9V between pins A (red) and C (blk).

Using a clip lead or other jumper wire, rap id ly short

to geth er pins A (red) and C (blk) of the 3-pin connector.

See Illustration below.

If working correctly, the console

should show a speed value.

RPM INPUT

Turn rotary switch to RPM and disconnect the RPM

sensor (no color tie) from the main harness. Check

harness RPM connector for 12V be tween pins B (wh)

and C (blk) and 9V between pins A (red) and C (blk).

Using a clip lead or other jumper wire, several times

rapidly short together pins A (red) and C (black) of

the 3-pin connector. If working correctly, the con sole

should show an RPM rate value.

Three-Pin Connector Testing

Troubleshooting

(cont)

Checking Console Inputs with Multimeter

REMOTE RUN/HOLD INPUT

Disconnect the remote run/hold sensor (or jumper

cover) from the main harness. Check harness remote

run/hold connector for 12V between pins B (wh) and

C (blk) and and 9V between pins A (red) and C (blk).

Placing a clip lead or other jumper wire between pins

A (red) and C (black) of the main harness run/hold

connector (gray tie) should turn off the “HOLD” icon on

the console display. Removing the jumper should turn

on the “HOLD” icon on the console display.

Содержание Calc-An-Acre II































Результаты поиска

Содержание Calc-An-Acre II

Отзывы:

Похожие инструкции для Calc-An-Acre II

Бренды по названию

Популярные бренды

micro-trak Calc-An-Acre II, Справочное руководство

Результаты поиска

Содержание Calc-An-Acre II

Отзывы:

Похожие инструкции для Calc-An-Acre II

Бренды по названию

Популярные бренды