background image

4

Table of Contents

Micro-Trak Warranty .............................................................................................................................................................................3
Table of Contents ..................................................................................................................................................................................4
Component Parts and Assembly Hardware .....................................................................................................................................5
Wiring Diagram ......................................................................................................................................................................................6
System Overview ...................................................................................................................................................................................7
Installation ..............................................................................................................................................................................................7

 Console Mounting ..................................................................................................................................................................................................7

 

Electrical Installation ..............................................................................................................................................................................................8

 

Speed Sensor Options ...........................................................................................................................................................................................9

 Astro 

Speed Sensor Installation .........................................................................................................................................................................9 

 Magnetic Speed Sensor Installation ..............................................................................................................................................................10

 

Optional Remote Run/Hold Kit Installation ................................................................................................................................................11

 

Optional Shaft RPM..............................................................................................................................................................................................12

Calc-An-Acre II Console Functions ...................................................................................................................................................13
Calibration ............................................................................................................................................................................................14

 

English/Metric Selection ....................................................................................................................................................................................14 

 

Entering Calibration Values ..............................................................................................................................................................................15

 

Fine Tuning Speed/Distance Cal .....................................................................................................................................................................17

Operation ..............................................................................................................................................................................................18

 General .....................................................................................................................................................................................................................19 

 

Width Reduction:  On-The-Go .........................................................................................................................................................................19

 

Rotary Switch Positions ......................................................................................................................................................................................19

 

Resetting System Counters ...............................................................................................................................................................................20

Troubleshooting ..................................................................................................................................................................................20

 Messages/Warnings .............................................................................................................................................................................................20

 General .....................................................................................................................................................................................................................21

 

Checking Individual Components ..................................................................................................................................................................22

 

Checking Console Inputs ...................................................................................................................................................................................23

Appendices ...........................................................................................................................................................................................24

 

Appendix A - Optional Speed Sensor Mounting Installation ...............................................................................................................25

 

                        Optional Speed Sensor Mounting Installation on Drive Shaft .................................................................................26

 

Appendix B - Radar “Y” Adapter Cables .......................................................................................................................................................27

 

Appendix C - Conversion Chart .......................................................................................................................................................................28

 

Appendix D - Replacement Parts ...................................................................................................................................................................29

Содержание Calc-An-Acre II































Отзывы: