MHSC CLLDVNS Скачать руководство пользователя страница 4

4

20302381

Designer Series Direct Vent Gas Fireplace

IMPoRTaNT SaFeTy INFoRMaTIoN & CoDe aPPRoVaL

12.  Do not use this fireplace to cook food or burn paper or 

other objects.

13.  Never place anything on top of fireplace.
14.  Do not use any solid fuels (wood, coal, paper, card-

board,  etc.)  in  this  fireplace.  Use  only  the  gas  type 
indicated on rating plate.

15.  This  appliance,  when  installed,  must  be  electrically 

grounded  in  accordance  with  local  codes  or  in  the 
absence  of  local  codes,  with  the 

National  Electrical 

Code, ANSI/NFPA 70

, or the 

Canadian Electrical Code, 

CSA C22.1.

16.  Do not obstruct the flow of combustion and ventilation 

air in any way. Provide adequate clearances around 
air openings into the combustion chamber along with 
adequate  accessibility  clearance  for  servicing  and 
proper operation.

17.  When the appliance is installed directly on carpeting, 

tile or other combustible material other than wood floor-
ing, you must set appliance on a metal or wood panel 
or hearth pad extending the full width and depth of the 
appliance.

18.  Do not use fireplace if any part has been exposed to 

or has been under water. Immediately call a qualified 
service technician to inspect the appliance and replace 
any part of the control system and any gas control which 
as been submerged in water.

19.  Do not operate fireplace if any log is broken.
20.  Do not use a blower insert, heat exchanger insert, or 

any  other  accessory  not  approved  for  use  with  this 
fireplace.

21.  Do not operate the fireplace with glass door removed, 

cracked, or broken.

CoDe aPPRoVaL 

Direct Vent type appliances draw all combustion air from 
outside of the dwelling through the vent pipe.
These appliances have been tested by CSA and found to 
comply with the established standards for DIRECT VENT 
GAS FIREPLACE HEATERS in the USA and Canada as 
follows:

LISTeD VeNTeD GaS FIRePLaCe heaTeR

TESTED TO: 

ANSI Z21.88-2009 / CSA 2.33-2009 STANDARDS

A  manufactured  home  (USA  only)  or  mobile  home  OEM 
installation  must  conform  with  the 

Manufactured  Home 

Construction and Safety Standard,

 

Title 24 CFR, Part 

3280, 

or  when  such  a  standard  is  not  applicable,  the 

Standard for Manufactured home Installations, aNSI/
NCSBCS a225.1

, or 

Standard for Gas equipped Recre-

ational Vehicles and Mobile housing, CSa Z240.4

WARNING

!

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

AVERTISSEMENT

!

Un panneau vitré chaud

 peut 

causer des brûlures.

Laissez refroidir le panneau

vitr

é

 avant d’y toucher.

Ne laisser jamais

 les enfants

toucher le panneau vitr

é

.

w

a

RNING

Never connect unit to private (non-utility) 
gas wells.  This gas is commonly known 
as wellhead gas.

IMPoRTaNT:

PLeaSe ReaD The FoLLowING 

CaReFuLLy 

It is normal for fireplaces fabricated of steel 
to give off some expansion and/or contraction 
noises during the start up or cool down cycle. 
Similar noises are found with your furnace heat 
exchanger or car engine. 

IMPoRTaNT:

PLeaSe ReaD The FoLLowING 

CaReFuLLy 

It is not unusual for gas fireplace to give off 
some odor the first time it is burned. This is due 
to the manufacturing process. 

Please ensure that your room is well 

ventilated during burn off — open all 

windows.

It is recommended that you burn your fireplace 
for at least ten (10) hours the first time you use 
it. Place the fan switch in the “OFF” position 
during this time.

Содержание CLLDVNS

































































Отзывы: