MHSC CLLDVNS Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 64

MHSC CLLDVNS Скачать руководство пользователя страница 13

20302381

13

Designer Series Direct Vent Gas Fireplace

CLeaRaNCeS

CLeaRaNCeS To CoMBuSTIBLeS

Follow these instructions carefully to ensure safe installation. Failure to
follow instructions exactly can create a fire hazard.
The appliance cannot be installed on a carpet, tile or other combustible
material other than wood flooring. If installed on carpet or vinyl flooring, the
appliance shall be installed on a metal, wood or noncombustible material
panel extending full width and depth of the appliance.

45°

1”

4”

5”

6”

”

3”

FP2818
mantel leg clearance

MaNTeL CLeaRaNCeS

NoTe:

The combustible area above the facing must

not protrude more than 1/2" from the facing. If it does,
it is considered a mantel and must meet the mantel
requirements listed in this manual.

Never obstruct or modify the air inlet or
outlet grilles (louvers). This may create
a fire hazard.

Figure 10 -
Mantel Clearance

72”

(1829 mm)

Min.

Ceiling

6”

(152 mm)

Min.

FP2832
ceiling wall clearance

Figure 9 -
Ceiling and Side Wall Clearances

Combustible Mantel

FP2544

Stud

Combustible
Material Area

FP2818

Top View

w

a

RNING

FP2817
mantel clearances

16”

12”

10”

12”

6”

2

56O

”

Side View

Noncombustible
Material to Top of
Standoffs

FP2817

Top of Fireplace
Opening

w

a

RNING

12"

(305 mm)

Max. Depth

16"

(406 mm)

Min.

Spacer

Side of Fireplace
Opening

«
...
11
12
13
14
15
...
»

Содержание CLLDVNS

































































Отзывы:

Нет отзывов