MHSC CLLDVNS Скачать руководство пользователя страница 3

20302381

3

Designer Series Direct Vent Gas Fireplace

4.   Never install the fireplace 

 

•  

in a recreational vehicle

 

•  

where curtains, furniture, clothing, or other flam-
mable objects are less than 42" from the front, top, 
or sides of the fireplace

 

•  

in high traffic areas

 

•  

in windy or drafty areas 

5.  This fireplace reaches high temperatures. Keep children 

and adults away from hot surfaces to avoid burns or 
clothing ignition. Fireplace will remain hot for a time after 
shutdown. Allow surfaces to cool before touching. 

6.  Young  children  should  be  carefully  supervised  when 

they are in the same room as the appliance. Toddlers, 
young children and others may be susceptible to acci-
dental contact burns. A physical barrier is recommended 
if there are at risk individuals in the house. To restrict 
access  to  a  fireplace  or  stove,  install  an  adjustable 
safety gate to keep toddlers, young children and other 
at risk individuals out of the room and away from hot 
surfaces. 

7.  Do not modify fireplace under any circumstances. Any 

parts removed for servicing must be replaced prior to 
operating fireplace. 

8.  Turn fireplace off and let cool before servicing, install-

ing, or repairing. Only a qualified service person should 
install,  service,  or  repair  the  fireplace.  Have  burner 
system  inspected  annually  by  a  qualified  service 
person. 

9.  You  must  keep  control  compartments,  burners,  and 

circulating air passages clean. More frequent cleaning 
may be needed due to excessive lint and dust. Turn off 
the gas valve and pilot light before cleaning fireplace. 

10.  Have venting system inspected annually by a qualified 

service person. If needed, have venting system cleaned 
or repaired. Refer to 

Cleaning and Maintenance

Page 

48.

11.  Keep the area around your fireplace clear of combus-

tible materials, gasoline, and other flammable vapor and 
liquids. Do not run fireplace where these are used or 
stored. Do not place items such as clothing or decora-
tions on or around fireplace. 

INSTaLLeR

Please leave these instructions with the appliance.

owNeR

Please retain these instructions for future reference.

IMPoRTaNT SaFeTy INFoRMaTIoN

This fireplace is a vented product. This fireplace must be 
properly installed by a qualified service person. The glass 
door must be properly seated and sealed. If this unit is not 
properly installed by a qualified service person with glass 
door properly seated and sealed, combustion leakage can 
occur. 

CaRBoN MoNoxIDe PoISoNING:

 Early signs of carbon 

monoxide poisoning are similar to the flu with headaches, 
dizziness and/or nausea. If you have these signs, the fire-
place may not have been installed properly. Get fresh air 
at once! Have the fireplace inspected and serviced by a 
qualified service person. Some people are more affected 
by carbon monoxide than others. These include pregnant 
women,  people  with  heart  or  lung  disease  or  anemia, 
those  under  the  influence  of  alcohol,  and  those  at  high 
altitudes. 
Propane/LP  gas  and  natural  gas  are  both  odorless. An 
odor-making agent is added to each of these gases. The 
odor helps you detect a gas leak. However, the odor added 
to these gases can fade. Gas may be present even though 
no odor exists.
Make certain you read and understand all warnings. Keep 
this manual for reference. It is your guide to safe and proper 
operation of this fireplace.
1.  This  appliance  is  only  for  use  with  the  type  of  gas 

indicated  on  the  rating  plate.  This  appliance  is  not 
convertible for use with other gases unless a certified 
kit is used. 

2.  For  propane/LP  fireplace,  do  not  place  propane/LP 

supply tank(s) inside any structure. Locate propane/LP 
supply tank(s) outdoors. To prevent performance prob-
lems, do not use propane/LP fuel tank of less than 100 
lbs. capacity. 

3.  If you smell gas

  shut off gas supply.

  do not try to light any appliance.

•  

do not touch any electrical switch; do not use any 
phone in your building .

•  

immediately call your gas supplier from a neighbor’s 
phone. Follow the gas supplier’s instructions.

• 

Read this owner’s manual carefully and completely before trying to assemble, operate, 
or service this fireplace. 

• 

any change to this fireplace or its controls can be dangerous.

• 

Improper installation or use of this fireplace can cause serious injury or death from 
fire, burns, explosions, electrical shock and carbon monoxide poisoning.

w

a

RNING

Содержание CLLDVNS

































































Отзывы: