manualshive.com logo in svg

MHS Boilers ADI LT, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
MHS Boilers ADI LT Скачать руководство пользователя страница 35

ADI LT boiler - Technical Manual 

 

                  Page 

L338 

 

11/2011 

35 

 

15.5 DRAINING OF THE BOILER CONDENSED PRODUCTS 
 
15.5.1. Water condensing 
 

Having the heat exchanger in stainless steel, the ADI LT boiler has no limit of the minimum return temperature. 
This allows obtaining a higher profit of the heat generated by the combustion products: 

- Sensible heat: the heat transferred due to the cooling of burnt gases. 
- Latent heat: the heat transferred due to the energy issuing from the water steam when it condenses and 
turns into liquid. 

 
The energetic efficiency added thanks to the use of the latent heat of the condensed products can be up to 11% in 
case of natural gas, which is the relation between the High Calorific Value (HCV) and the Low Calorific Value 
(LCV). 
 
The theoretical volume of the condensed products can be: 
 

- 1,63 kg / m3 

 

- up to 0,14 kg / kWh 

 
15.5.2. Neutralization treatment of the condensed products. 
 

For natural gas, the condensed water has a pH value that can be between 3,5 and 5,5. 
 
It is recommended to realize a neutralization treatment of the condensed products before throwing them to the 
general drainage of the building, or similar. 
 
Generally, you have to make the condensed products circulate mixed with a sort of powder, which can be calcium 
carbonate, hydrolyte of magnesium (salt formed by calcium hydride, CaH2, and magnesium) or similar, in order to 
neutralize them, which means to increase the value of its pH so that it will be between 6,5 and 9. 
 
It is recommended to realize periodical measurements of the water pH after the neutralization treatment: when the 
value measured is lower than 6,5 it is recommended to replenish with the powder.  
 
In any case, the neutralization treatment must be realized in conformity with the local, autonomic and national laws. 
 
The neutralization system should be placed at a level of height lower than the boiler draining/outlet of the 
condensed products. If this is not possible, consider the installation of a pump of condensed products. 

 

 

15.5.3. Evacuation piping of condensed products. 
 

- The boiler outlet of the condensed products should be connected to a siphon. 
   (Fill the siphon with clean water before starting the boiler). 
 
- Some boiler models should be placed on a base with sufficient height to allow the installation of the draining of the 
condensed products, of the siphon and of the connection to the neutralization piping of the condensed products. 
 
- The evacuation of the condensed products to the general drainage should be realized in a visible way, through a 
visible connection, open funnel or similar. 
 
- Due to the characteristics of the condensed water, the material of the piping must be resistant to the action of the 
acid water, for example: plastics (P.V.C). 
 
- The evacuation pipe must have a minimum slope of 30 mm / metre 
 
- Drainage by means of an external piping is not recommended, due to the risks of condensation and corrosion. 

 
15.5.4. Boiler chimney 

The chimney must be realized with materials that are resistant to condensed water, which is acid. 
The gaskets joining the components of the chimney must be watertight. 
The chimney must comply with the national and European regulations. 
 

Содержание ADI LT




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды