Carton contains the following components for the cart mounting:
Please check to be sure that all parts are included before proceeding.
Contact your dealer or the factory if any parts are missing.
Long Legs
2
2
2
2
Short Legs
2
2
2
2
Lower Shelf Frame
1
1
1
1
Stainless Grease Cup
1
1
1
1
8" Rubber Wheels
2
2
2
2
Axle 22 1/2"
1
1
1
1
Axle Hitch Pins
2
2
2
2
Axle Washers
2
2
2
2
Hub Caps
2
2
2
2
Hose Retaining Ring
1
1
1
1
1/4-20x1-1/2 Slotted Bolt
10
10
8
8
1/4-20x3/4 Slotted Bolt
2
2
4
4
1/4-20 Kep Nut
10
10
8
8
10-24x1/2" Rd.Hd. Slot
1
1
1
1
10-x24 Kep Nut
1
1
1
1
12' Nat. Gas Hose Kit
N/A
1
N/A
1
CART HARDWARE WCP4 WCN4 JCP4 JCN4
Grill Heads (WNK4,WRG4,WHRG4, (JNR4)
TJK2,TRG2,THRG2)
Tank Ring Kit
Tank Ring
1
N/A
1
N/A
1/4-20x1-1/2" Slotted Bolt
1
N/A
1
N/A
1/4-20x 3/4" Hex Bolt
1
N/A
1
N/A
1/4-20 Thumb Screw
1
N/A
1
N/A
1/4-20 Kep Nut
3
N/A
3
N/A
Complete View of Cart Assembly
Step 1: Leg Assembly
(Fig 2)
1. Tip the grill head bottom on end as shown in Fig. 2
(TIP: work on protected area such as: carpet, tarp
or one of the boxes to protect cart finish
.
2. Attach the two short legs to the left end of the grill
head bottom with the “Hose Ring Hole” leg facing
grill front.
Note: The short legs are stamped on
the inside (Front or Back).
Use two 1/4-20x1-1/2"
slotted bolts for each leg. Insert bolts from inside
grill box, attach leg and fasten with 1/4-20 Kep nuts.
3. Attach the two long legs to the right end of the grill
head bottom. Use two 1/4-20x1-1/2" slotted bolts
for each leg, insert bolts from inside grill box, attach
leg and fasten with 1/4-20 Kep nuts.
4. Attach the hose clamp ring to the front left short leg
with the 10x24x1/2" Rd. Hd. slotted bolt.
FINGER TIGHTEN ALL BOLTS UNTIL
LOWER SHELF IS ATTACHED.
Step 2: Lower Shelf and Axle Assembly
1. Bolt shelf to the (4) legs as follow:
(A) WCP and WCN (
Fig. 3)
carts uses (2) 1/4-20x
1-1/2" slotted bolts and Kep nuts to fasten the
frame to the long legs and (2) 1/4-20x3/4" slotted
head bolts to fasten the frame to the short legs.
(B) JCP and JCN
(Fig. 4)
carts use (4) 1/4-20x
3/4" slotted head bolts to fasten the frame at all 4
corners.
Note: Do Not Completely Tighten At This Point
2. Install (1) axle hitch pin into the small end hole
and install washer. Slide (1) wheel onto axle, hub-
cap side out.
3. Slide open axle end through the short leg holes
and install remaining wheel, washer and hitch pin.
Install hubcaps after the cart bolts are completely
tightened.
Stand grill upright to seat legs and tighten all bolts
and nuts making legs and frame rigid. Recheck fas-
teners for tightness.
FIG. 2
FIG. 1
Mountings
6
Duro-Cast Cart
Содержание JNR4DD Series
Страница 33: ...Parts Information TJK LID STAINLESS DROP DOWN SHELF IDENTIFICATION GGDDSSUS 33 32...
Страница 36: ...NOTES 36...
