MGE UPS Systems 11+ Скачать руководство пользователя | Manualshive

Страница: 70 / 76

background image

dBrnC

Decibel above reference noise.

DC or dc

Direct current, or voltage.

Earth ground

A ground circuit that has contact with the earth.

Electrician

Refers to an installation electrician qualified to install heavy-duty electrical components in
accordance with local codes and regulations. Not necessarily qualified to maintain or repair
electrical or electronic equipment.

FET

Field effect transistor.

Freq.

Frequency.

Frequency slew rate

The change in frequency per unit of time. Given in term of Hz per second (Hz/sec.).

GND

Ground (safety).

Hz

Hertz, frequency measurement unit, 1Hz is one cycle per second.

I

Current.

IEC

International Electrotechnical Commission.

IEEE

Institute of Electrical and Electronic Engineers.

IGBT

Insulated gate bipolar transistors.

Input branch circuit

The input circuit from the building power panel to the equipment.

Inverter

An electrical circuit that generates an AC voltage source from a DC voltage source.

Inverter mode

See “on-line” mode.

I/O

Input/Output.

I/T or IT

Information Technology.

kVA

KiloVolt-Ampere; is equal to 1000 Volt-Ampere.

L

Line.

LCD

Liquid-Crystal Display unit.

LED

Light Emitting Diode.

Mains or Mains 1

Main AC input source.

Mains 2

Bypass AC input source.

mA

Milliampere.

MAX.

Maximum.

MCM

Thousand circular mil; standard wire sizes for multiple stranded conductors over 4/0 AWG
in diameter. M is from Roman numerical system indicating 1000.

N

Neutral.

NC

Normally closed.

NEC

National Electrical Code.

NFPA

National Fire Protection Association.

NO

Normally open.

EX 5/7/11 RT Systems

Glossary

G — 2

86-86000-00 B01

«
...
68
69
70
71
72
...
»

Содержание 11+













































































Отзывы:

Нет отзывов

Похожие инструкции для 11+

SuperCap 1000VA

Бренд: Marathon Страницы: 48

Бренд: Sy-G Страницы: 31

Бренд: PROLiNK Страницы: 25

Бренд: Eaton Страницы: 62

Бренд: CyberPower Страницы: 2

Бренд: Monster Power Страницы: 49

Бренд: Centralion Страницы: 8

Бренд: Eaton Страницы: 114

Бренд: Eaton Страницы: 7

Бренд: Centralion Страницы: 9

Бренд: Centralion Страницы: 13

Бренд: Centralion Страницы: 33

Бренд: Centralion Страницы: 40

Бренд: OPTI-UPS Страницы: 24

Бренд: LEGRAND Страницы: 44

Бренд: Faller Страницы: 8

Бренд: Eaton Страницы: 38

Tripp Lite Series SmartPro Series

Бренд: Eaton Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды