manualshive.com logo in svg

MGE UPS Systems 11+, Инструкция по установке и эксплуатации

Поделиться
Скачать
MGE UPS Systems 11+ Скачать руководство пользователя страница 11

Installation and User Manual

c vii

86-86000-00 B01

Safety of Persons

CAUTION: Safety of persons

◗

The system has its own power source (the battery). Consequently, the power outlets may be energized even if the 
systems is disconnected from the AC power source.

◗

Dangerous voltage levels are present within the system. It should be opened exclusively by qualified service personnel.

◗

The system must be properly grounded. 

◗

The battery supplied with the system contains small amounts of toxic materials. To avoid accidents, the directives listed 

below must be observed:

-Never burn the battery (risk of explosion).
-Do not attempt to open the battery (the electrolyte is dangerous for the eyes and skin).
-Comply with all applicable regulations for the disposal of the battery.
-Batteries constitute a danger (electrical shock, burns). The short-circuit current may be very high. Precautions must be 
taken for all handling: remove watches, rings, bracelets and any other metal objects, use tools with insulated handles.
-Do not lay tools or metal parts on top of batteries.

CAUTION: Product Safety

◗

The UPS connection instructions and operation described in the manual must be followed in the indicated order.

◗

A protection circuit breaker must be installed upstream and be easily accessible. The system can be disconnected from
the AC power source by opening this circuit breaker.

◗

Check that the indications on the rating plate correspond to your AC powered system and to the actual electrical
consumption of all the equipment to be connected to the system.

◗

Never install the system near liquids or in an excessively damp environment.

◗

Never let a foreign body penetrate inside the system.

◗

Never block the ventilation grates of the system.

◗

Never expose the system to direct sunlight or source of heat.

◗

If the system must be stored prior to installation, storage must be in a dry place.

◗

The admissible storage temperature range is -25ºC to +55ºC.

Special Precautions

◗

All handling operations will require at least two people (unpacking, installation in rack system).

◗

Before and after the installation, if the UPS remains de-energized for a long period, the UPS must be energized for a
period of 24 hours, at least once every 6 months (for a normal storage temperature less than 25°C). This charges the
battery, thus avoiding possible irreversible damage.

◗

During the replacement of the Battery Module, it is imperative to use the same type and number of element as the original
Battery Module provided with the UPS to maintain an identical level of performance and safety. In case of doubt, don’t
hesitate to contact your MGE Office Protection Systems representative.

Environment

◗

This product has been designed to respect the environment:

It does not contain any Chlorofluorocarbon (CFC) or Hydrochlorofluorocarbon (HCFC).

◗

UPS recycling at the end of service life:

MGE Office Protection Systems undertakes to recycle, by certified companies and in compliance with all appli-
cable regulations, all UPS products recovered at the end of their service life (contact your MGE Office Protection
Systems branch office).

◗

Packing:

UPS packing materials must be recycled in compliance with all applicable regulations.

WARNING: 

This product contains lead-acid batteries. Lead is a dangerous substance for the environment if it

is not properly recycled by specialized companies.

Содержание 11+













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды