MGE UPS Systems 11+ Скачать руководство пользователя

Страница: 42 / 76

2.7.3

Connections with Separate Normal and Bypass AC Sources (2 Mains)

CAUTION:

This connection requires isolation Transformer Module. Please visit our web site
www.mgeops.com or call (800) 279-7776.

Figure 2-14: Normal AC and Bypass AC inputs, Output Cables Installation, and Simplified Connection Diagram.

NOTE:

Please visit our web site www.mgeops.com or call (800) 279-7776 for assistance
with separate, normal AC, and bypass AC input support.

NOTE:

With parallel redundance connection, two input transformers are needed for
separate, normal, and AC bypass input. Please visit our web site
www.mgeops.com for details.

Card Settings

RS232 Download

66074

UPS

data

Reset

100 10

1 2

ETHERNET

MAC=

55E

Output

Bypass

Normal

OFF

To Load or

Transformer Module (if applicable)

MAINS 2

BYPASS AC

NORMAL AC

MAINS 1

LOAD

With separate Normal and Bypass AC inputs, supplied by separate sources.

Isolation

Transformer

(PN 86211)

EX 5/7/11 RT Systems

Installation

2 — 16

86-86000-00 B01

Proceed as follows:

Remove the cover plate under the I/O Box. Loosen the terminal blocks
L1 and L3, and remove the jumper.

CAUTION:

Always connect the earth ground wire first.

Install Normal AC, Bypass AC and output cables as shown.

Reinstall the cover plate under the I/O Box with four screws.

Secure the I/O Box to the Power Module with three screws.

See Section 2.7.2 for connecting EX RT Transformer module, if applicable.

Содержание 11+













































































Результаты поиска

Содержание 11+

Отзывы:

Похожие инструкции для 11+

Бренды по названию

Популярные бренды

MGE UPS Systems 11+, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 11+

Отзывы:

Похожие инструкции для 11+

Бренды по названию

Популярные бренды